Претраживање
Приказ резултата 11-20 од 34
Structural and Electrical Properties of Ti Doped alpha-Fe2O3
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2013)
In this work we have analyzed the effects of Ti doping on structural and electrical properties of alpha-Fe2O3. When the amount of added Ti (5 wt.% TiO2) was within the solubility degree and XRD, SEM and EDS analysis revealed ...
Investigation of Sintering Kinetics of Magnesium Titanate
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2013)
Obtaining new materials including sintered electronic materials using different procedures is the consequence of long complex and expensive experimental work. However, the dynamics of expansive development of electronic ...
Advantages of Combined Sintering Compared to Conventional Sintering of Mechanically Activated Magnesium Titanate
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2014)
In this article, the advantages of combined sintering in comparison with the conventional one, of mechanically activated magnesium titanate ceramic were investigated. The stoichiometric mixtures of MgO and TiO2 were ...
Microstructural and Electrical Properties of Cordierite-based Ceramics Obtained After Two-step Sintering Technique
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2016)
Cordierite-based ceramic materials are attracting much interest for their various applications in industry, for manufacturing multilayer circuit boards, catalytic converters, filters, thermal insulation, kiln furniture, ...
Sintering Process Influence on Microstructure and Intergranular Impedance of Rare-Earth Modified BaTiO3-Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
Sintering process is a complex of different synergetic effects during the ceramics materials consolidation. The microstructural level properties control is very important as a stage in advanced materials prognosis. SEM ...
Analysis and Modeling of Sintering of Sr-hexaferrite Produced by PIM Technology
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
The powder injection moulding (PIM) technology is lately becoming more and more significant due to complex design possibilities and good repeatability. This technology requires optimization of all steps starting with ...
Influence of mechanical activation on microstructure and crystal structure of sintered MgO-TiO2 system
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2010)
Mixtures of MgO-TiO2 were mechanically activated using high-energy planetary ball mill during 5, 10, 20, 40, 80 and 120 minutes. Sintering process was preformed in air at 1100°-1400°C for 2h. The decrease in powder's ...
The Influence of Mechanical Activation on Sintering Process of BaCO3-SrCO3-TiO2 System
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2012)
In this article the influence of mechanical activation on sintering process of barium-strontium-titanate ceramics has been investigated. Both non-activated and mixtures treated in a planetary ball mill for 5, 10, 20, 40, ...
Electrical Properties and Microstructure Fractal Analysis of Magnesium-Modified Aluminium-Silicate Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
The addition of Mg(2)(NO)(3) and some active additives, composed of Al salts, to the mixtures of kaolinite and bentonite can provide clay compositions which, after sintering at high temperatures, produce very porous ceramics ...
Physical Properties of Sintered Alumina Doped with Different Oxides
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
Corundum (alpha-alumina) is a suiTab. material for usage in various industry fields owing to its chemical stability, electrical and mechanical features. It is known that properties of ceramics could be modified by addition ...