Pretraživanje
Prikaz rezultata 11-20 od 34
Investigation of Sintering Kinetics of Magnesium Titanate
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2013)
Obtaining new materials including sintered electronic materials using different procedures is the consequence of long complex and expensive experimental work. However, the dynamics of expansive development of electronic ...
Sintering Process Influence on Microstructure and Intergranular Impedance of Rare-Earth Modified BaTiO3-Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
Sintering process is a complex of different synergetic effects during the ceramics materials consolidation. The microstructural level properties control is very important as a stage in advanced materials prognosis. SEM ...
Structural and Electrical Properties of Ti Doped alpha-Fe2O3
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2013)
In this work we have analyzed the effects of Ti doping on structural and electrical properties of alpha-Fe2O3. When the amount of added Ti (5 wt.% TiO2) was within the solubility degree and XRD, SEM and EDS analysis revealed ...
Electrical Properties and Microstructure Fractal Analysis of Magnesium-Modified Aluminium-Silicate Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
The addition of Mg(2)(NO)(3) and some active additives, composed of Al salts, to the mixtures of kaolinite and bentonite can provide clay compositions which, after sintering at high temperatures, produce very porous ceramics ...
Isothermal kinetics of titanium-oxo-alkoxy clusters formation
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
In this article, the influences of titanium tetraisopropoxide Ti(OR)4 (R = Pri) concentration, molar ratio, h = [H2O]/[Ti(OR)4], and temperature, on the formation kinetics of the titanium-oxo-alkoxy clusters (TOAC), were ...
Sintering of Mechanically Activated Magnesium-titanate and Barium-zinc-titanate Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
In this article the influence of mechanical activation on sintering process of magnesium-titanate and barium-zinc-titanate ceramics has been investigated. Both non-activated and mixtures treated in planetary ball mill for ...
Analysis and Modeling of Sintering of Sr-hexaferrite Produced by PIM Technology
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
The powder injection moulding (PIM) technology is lately becoming more and more significant due to complex design possibilities and good repeatability. This technology requires optimization of all steps starting with ...
Influence of mechanical activation on microstructure and crystal structure of sintered MgO-TiO2 system
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2010)
Mixtures of MgO-TiO2 were mechanically activated using high-energy planetary ball mill during 5, 10, 20, 40, 80 and 120 minutes. Sintering process was preformed in air at 1100°-1400°C for 2h. The decrease in powder's ...
The Influence of Mechanical Activation on Sintering Process of BaCO3-SrCO3-TiO2 System
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2012)
In this article the influence of mechanical activation on sintering process of barium-strontium-titanate ceramics has been investigated. Both non-activated and mixtures treated in a planetary ball mill for 5, 10, 20, 40, ...
Structure and photocatalytic properties of sintered TiO2 nanotube arrays
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
One-dimensional (1D) TiO2 nanotubes perpendicular to the substrate were obtained by electrochemical oxidation of titanium foil in an acid electrolyte. In order to alter the crystallinity and the morphology of films the ...