TY  - JOUR
AU  - Terzić, Anja
AU  - Radojević, Zagorka
AU  - Pavlović, Ljubica
AU  - Pavlović, Vladimir
AU  - Mitić, Vojislav
PY  - 2015
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/3770
AB  - In this study, the feasibility of using fly ash to manufacture high-temperature mortars was investigated. The investigation was set to define preliminary characteristics of new types of mortars based on ordinary and/or refractory cement with fly ash addition, and to establish mutual correlation between thermally induced changes of mineral phases, microstructure, and final performances of the mortars. New mortars, made up of 21% cement (PC-CEM I 42.5R/HAC-Secar 70/71), 70% river sand, and 9% fly ash, were chemically, physically, and mechanically characterized to determine possibilities of fly ash re-utilization for high-temperature purposes. The fly ash samples, which originated from four different power plants, were mechanically activated. Mortars were heat-treated up to 1300 degrees C in a laboratory tunnel furnace with retention time 2 h. Thermal stability of crystalline phases were studied by differential thermal analysis (DTA); thermally induced changes in mineral phase composition were analyzed by XRD; and microstructure were investigated by scanning electron microscopy. Correlated results of DTA, XRD, and SEM analyses indicated initiation of sintering processes at approximately 1300 degrees C and formation of thermally stable minerals (rankinite, gehlenite, anorthite, cristobalite). The investigation highlights a sustainable approach of using fly ash in developing ecofriendly mortars for high-temperature application.
PB  - Wiley, Hoboken
T2  - International Journal of Applied Ceramic Technology
T1  - Novel Utilization of Fly Ash for High-Temperature Mortars: Phase Composition, Microstructure and Performances Correlation
EP  - 146
IS  - 1
SP  - 133
VL  - 12
DO  - 10.1111/ijac.12135
ER  - 

@article{
author = "Terzić, Anja and Radojević, Zagorka and Pavlović, Ljubica and Pavlović, Vladimir and Mitić, Vojislav",
year = "2015",
abstract = "In this study, the feasibility of using fly ash to manufacture high-temperature mortars was investigated. The investigation was set to define preliminary characteristics of new types of mortars based on ordinary and/or refractory cement with fly ash addition, and to establish mutual correlation between thermally induced changes of mineral phases, microstructure, and final performances of the mortars. New mortars, made up of 21% cement (PC-CEM I 42.5R/HAC-Secar 70/71), 70% river sand, and 9% fly ash, were chemically, physically, and mechanically characterized to determine possibilities of fly ash re-utilization for high-temperature purposes. The fly ash samples, which originated from four different power plants, were mechanically activated. Mortars were heat-treated up to 1300 degrees C in a laboratory tunnel furnace with retention time 2 h. Thermal stability of crystalline phases were studied by differential thermal analysis (DTA); thermally induced changes in mineral phase composition were analyzed by XRD; and microstructure were investigated by scanning electron microscopy. Correlated results of DTA, XRD, and SEM analyses indicated initiation of sintering processes at approximately 1300 degrees C and formation of thermally stable minerals (rankinite, gehlenite, anorthite, cristobalite). The investigation highlights a sustainable approach of using fly ash in developing ecofriendly mortars for high-temperature application.",
publisher = "Wiley, Hoboken",
journal = "International Journal of Applied Ceramic Technology",
title = "Novel Utilization of Fly Ash for High-Temperature Mortars: Phase Composition, Microstructure and Performances Correlation",
pages = "146-133",
number = "1",
volume = "12",
doi = "10.1111/ijac.12135"
}

Terzić, A., Radojević, Z., Pavlović, L., Pavlović, V.,& Mitić, V.. (2015). Novel Utilization of Fly Ash for High-Temperature Mortars: Phase Composition, Microstructure and Performances Correlation. in International Journal of Applied Ceramic Technology
Wiley, Hoboken., 12(1), 133-146.
https://doi.org/10.1111/ijac.12135

Terzić A, Radojević Z, Pavlović L, Pavlović V, Mitić V. Novel Utilization of Fly Ash for High-Temperature Mortars: Phase Composition, Microstructure and Performances Correlation. in International Journal of Applied Ceramic Technology. 2015;12(1):133-146.
doi:10.1111/ijac.12135 .

Terzić, Anja, Radojević, Zagorka, Pavlović, Ljubica, Pavlović, Vladimir, Mitić, Vojislav, "Novel Utilization of Fly Ash for High-Temperature Mortars: Phase Composition, Microstructure and Performances Correlation" in International Journal of Applied Ceramic Technology, 12, no. 1 (2015):133-146,
https://doi.org/10.1111/ijac.12135 . .

TY  - CONF
AU  - Terzić, Anja
AU  - Radojević, Zagorka
AU  - Miličić, Ljiljana
AU  - Obradović, Nina
AU  - Pavlović, Vladimir B.
AU  - Pavlović, Ljubica
PY  - 2013
UR  - http://dais.sanu.ac.rs/123456789/413
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5671
AB  - As coal combustion byproduct fly ash represents a risk for environment: direct ash emission from open land-fills causes pollution of air, soil and water. The solution for this severe pollution problem is fly ash reapplication in various construction ceramic composite materials. Although pelletization of waste powdery material is a known technique in the production of artificial aggregates, it still has not been widely used in construction sector. Here investigated cold-bonded fly ash aggregate was produced in semi-industrial pelletizing device. The fly ash particles were bonded with water-glass (Sodium silicate - Na2SiO3) and used as substitution for aggregate in Portland cement based composite. Half of the produced lightweight aggregate was submitted to thermal treatment and afterwards applied in the construction composite in the same ration as in the case of cold-bonded pellets. The performance characteristics of two types of lightweight composites were mutually compared and afterwards correlated with characteristics of normal-weight concrete. Compressive strength, modulus of elasticity and tensile strength were used as represents of the composites mechanical behavior. Mineral constituents of fly ash pellets were analyzed by means of X-ray diffraction analysis, differential thermal analysis was applied in crystalline phase investigation, and scanning electron microscopy in microstructural analysis. The leaching behavior and environmental impact of hazardous elements were also analyzed. It was concluded that content of potentially toxic elements found in leachate of fly-ash based composites was far below tolerance limit proposed by actual standards for the building materials, characterizing the fly ash non-harmful secondary raw material and enabling its reapplication in building materials industry. Utilizing fly ash to produce quality aggregates should yield significant environmental benefits.
PB  - Belgrade : Serbian Ceramic Society
C3  - Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : II Serbian Ceramic Society Conference, Sep 30th-Oct 1st, 2013, Belgrade
T1  - Lightweight construction ceramic composites based of pelletized fly ash aggregate
EP  - 33
SP  - 32
UR  - https://hdl.handle.net/21.15107/rcub_dais_413
ER  - 

@conference{
author = "Terzić, Anja and Radojević, Zagorka and Miličić, Ljiljana and Obradović, Nina and Pavlović, Vladimir B. and Pavlović, Ljubica",
year = "2013",
abstract = "As coal combustion byproduct fly ash represents a risk for environment: direct ash emission from open land-fills causes pollution of air, soil and water. The solution for this severe pollution problem is fly ash reapplication in various construction ceramic composite materials. Although pelletization of waste powdery material is a known technique in the production of artificial aggregates, it still has not been widely used in construction sector. Here investigated cold-bonded fly ash aggregate was produced in semi-industrial pelletizing device. The fly ash particles were bonded with water-glass (Sodium silicate - Na2SiO3) and used as substitution for aggregate in Portland cement based composite. Half of the produced lightweight aggregate was submitted to thermal treatment and afterwards applied in the construction composite in the same ration as in the case of cold-bonded pellets. The performance characteristics of two types of lightweight composites were mutually compared and afterwards correlated with characteristics of normal-weight concrete. Compressive strength, modulus of elasticity and tensile strength were used as represents of the composites mechanical behavior. Mineral constituents of fly ash pellets were analyzed by means of X-ray diffraction analysis, differential thermal analysis was applied in crystalline phase investigation, and scanning electron microscopy in microstructural analysis. The leaching behavior and environmental impact of hazardous elements were also analyzed. It was concluded that content of potentially toxic elements found in leachate of fly-ash based composites was far below tolerance limit proposed by actual standards for the building materials, characterizing the fly ash non-harmful secondary raw material and enabling its reapplication in building materials industry. Utilizing fly ash to produce quality aggregates should yield significant environmental benefits.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : II Serbian Ceramic Society Conference, Sep 30th-Oct 1st, 2013, Belgrade",
title = "Lightweight construction ceramic composites based of pelletized fly ash aggregate",
pages = "33-32",
url = "https://hdl.handle.net/21.15107/rcub_dais_413"
}

Terzić, A., Radojević, Z., Miličić, L., Obradović, N., Pavlović, V. B.,& Pavlović, L.. (2013). Lightweight construction ceramic composites based of pelletized fly ash aggregate. in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : II Serbian Ceramic Society Conference, Sep 30th-Oct 1st, 2013, Belgrade
Belgrade : Serbian Ceramic Society., 32-33.
https://hdl.handle.net/21.15107/rcub_dais_413

Terzić A, Radojević Z, Miličić L, Obradović N, Pavlović VB, Pavlović L. Lightweight construction ceramic composites based of pelletized fly ash aggregate. in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : II Serbian Ceramic Society Conference, Sep 30th-Oct 1st, 2013, Belgrade. 2013;:32-33.
https://hdl.handle.net/21.15107/rcub_dais_413 .

Terzić, Anja, Radojević, Zagorka, Miličić, Ljiljana, Obradović, Nina, Pavlović, Vladimir B., Pavlović, Ljubica, "Lightweight construction ceramic composites based of pelletized fly ash aggregate" in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : II Serbian Ceramic Society Conference, Sep 30th-Oct 1st, 2013, Belgrade (2013):32-33,
https://hdl.handle.net/21.15107/rcub_dais_413 .

TY  - JOUR
AU  - Terzić, Anja
AU  - Pavlović, Ljubica
AU  - Obradović, N.
AU  - Pavlović, Vladimir
AU  - Stojanović, J.
AU  - Milicić, Lj.
AU  - Radojević, Z.
AU  - Ristić, M.M.
PY  - 2012
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/3064
AB  - Amount of fly ash which is and yet to be generated in the coming years highlights the necessity of developing new methods of the recycling where this waste can be reused in significant quantity. A new possibility for fly ash utilization is in high-temperature application (thermal insulators or/and refractory material products). As such, fly ash has to adequately answer the mechanical and thermal stability criteria. One of the ways of achieving it is by applying mechanical activation procedure on fly ash. In present study, fly ashes from two different power plants were mechanically activated in a planetary ball mill. Mechanically treated fly ashes were cemented with two different binders: standard Portland cement and high-aluminates cement. Physico-chemical analysis and investigation of mineralogical components of composites are emphasized, due to the changes occurred in fly ash during mechanical activation and sintering of composites. Macro-performance of the composites was correlated to the microstructure of fly ash studied by means of XRD and SEM analysis. Thermal stability of crystalline phases was investigated with DTA. Highlight was placed on determination of relationship between mechanically activated fly ash and obtained composites microstructure on one side and behavior of sintered composites on the other side.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Synthesis and Sintering of High-temperature Composites Based on Mechanically Activated Fly Ash
EP  - 146
IS  - 2
SP  - 135
VL  - 44
DO  - 10.2298/SOS1202135T
ER  - 

@article{
author = "Terzić, Anja and Pavlović, Ljubica and Obradović, N. and Pavlović, Vladimir and Stojanović, J. and Milicić, Lj. and Radojević, Z. and Ristić, M.M.",
year = "2012",
abstract = "Amount of fly ash which is and yet to be generated in the coming years highlights the necessity of developing new methods of the recycling where this waste can be reused in significant quantity. A new possibility for fly ash utilization is in high-temperature application (thermal insulators or/and refractory material products). As such, fly ash has to adequately answer the mechanical and thermal stability criteria. One of the ways of achieving it is by applying mechanical activation procedure on fly ash. In present study, fly ashes from two different power plants were mechanically activated in a planetary ball mill. Mechanically treated fly ashes were cemented with two different binders: standard Portland cement and high-aluminates cement. Physico-chemical analysis and investigation of mineralogical components of composites are emphasized, due to the changes occurred in fly ash during mechanical activation and sintering of composites. Macro-performance of the composites was correlated to the microstructure of fly ash studied by means of XRD and SEM analysis. Thermal stability of crystalline phases was investigated with DTA. Highlight was placed on determination of relationship between mechanically activated fly ash and obtained composites microstructure on one side and behavior of sintered composites on the other side.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Synthesis and Sintering of High-temperature Composites Based on Mechanically Activated Fly Ash",
pages = "146-135",
number = "2",
volume = "44",
doi = "10.2298/SOS1202135T"
}

Terzić, A., Pavlović, L., Obradović, N., Pavlović, V., Stojanović, J., Milicić, Lj., Radojević, Z.,& Ristić, M.M.. (2012). Synthesis and Sintering of High-temperature Composites Based on Mechanically Activated Fly Ash. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 44(2), 135-146.
https://doi.org/10.2298/SOS1202135T

Terzić A, Pavlović L, Obradović N, Pavlović V, Stojanović J, Milicić L, Radojević Z, Ristić M. Synthesis and Sintering of High-temperature Composites Based on Mechanically Activated Fly Ash. in Science of Sintering. 2012;44(2):135-146.
doi:10.2298/SOS1202135T .

Terzić, Anja, Pavlović, Ljubica, Obradović, N., Pavlović, Vladimir, Stojanović, J., Milicić, Lj., Radojević, Z., Ristić, M.M., "Synthesis and Sintering of High-temperature Composites Based on Mechanically Activated Fly Ash" in Science of Sintering, 44, no. 2 (2012):135-146,
https://doi.org/10.2298/SOS1202135T . .

TY  - CONF
AU  - Terzić, Anja
AU  - Pavlović, Ljubica
AU  - Obradović, Nina
AU  - Pavlović, Vladimir B.
AU  - Radojević, Zagorka
AU  - Miličić, Ljiljana
AU  - Aćimović Pavlović, Zagorka
PY  - 2012
UR  - http://dais.sanu.ac.rs/123456789/532
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5690
AB  - The aim of the presented study is to evaluate utilization potential of the fly ash which is the main residue from the coal combustion thermal-plants. Decades long high production of fly ash represents extreme hazard for the environment. The storage problem of this waste material is also alerting. Thus, recycling and reapplication of fly ash in construction materials industry is the only economic solution. The well-known examples of fly-ash reapplication as a component in cement, mortar, concrete, bricks and tiles are not enough in means of reusing extreme amounts of this waste material. Therefore, new applications in ash-based composites have to be developed: eco-ceramic materials and sintered materials for refractory performances. In this investigation, characterization of three different fly ash capacities was used as base for further fly ash utilization possibilities analysis. Accent was on the investigation of the fly ash mineralogical and chemical composition. Thermal stability of crystalline phases was investigated with DTA. Macro-performance was correlated with the microstructure of fly ash studied by means of XRD and SEM analysis. Furthermore, content of trace elements, physico-chemical characteristics and leaching toxicity tests were carried out. Comparing the properties of investigated fly ashes with standard values, it could be presumed that fly ash originating from Serbian power plants can be potentially useful for high value products - eco-ceramic and refractory/sintered materials manufacturing. Key words: fly ash, microstructure, potential reusing, eco-ceramic, sintering.
Acknowledgements: This investigation was supported by Serbian Ministry of Science and Education and it was conducted under following projects: 172057 and 45008.
PB  - Belgrade : Serbian Ceramic Society
C3  - The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts
T1  - Evaluation of Fly Ash Pysico-chemical Characteristics as Component for Eco-ceramic and Sintered Materials
EP  - 32
SP  - 32
UR  - https://hdl.handle.net/21.15107/rcub_dais_532
ER  - 

@conference{
author = "Terzić, Anja and Pavlović, Ljubica and Obradović, Nina and Pavlović, Vladimir B. and Radojević, Zagorka and Miličić, Ljiljana and Aćimović Pavlović, Zagorka",
year = "2012",
abstract = "The aim of the presented study is to evaluate utilization potential of the fly ash which is the main residue from the coal combustion thermal-plants. Decades long high production of fly ash represents extreme hazard for the environment. The storage problem of this waste material is also alerting. Thus, recycling and reapplication of fly ash in construction materials industry is the only economic solution. The well-known examples of fly-ash reapplication as a component in cement, mortar, concrete, bricks and tiles are not enough in means of reusing extreme amounts of this waste material. Therefore, new applications in ash-based composites have to be developed: eco-ceramic materials and sintered materials for refractory performances. In this investigation, characterization of three different fly ash capacities was used as base for further fly ash utilization possibilities analysis. Accent was on the investigation of the fly ash mineralogical and chemical composition. Thermal stability of crystalline phases was investigated with DTA. Macro-performance was correlated with the microstructure of fly ash studied by means of XRD and SEM analysis. Furthermore, content of trace elements, physico-chemical characteristics and leaching toxicity tests were carried out. Comparing the properties of investigated fly ashes with standard values, it could be presumed that fly ash originating from Serbian power plants can be potentially useful for high value products - eco-ceramic and refractory/sintered materials manufacturing. Key words: fly ash, microstructure, potential reusing, eco-ceramic, sintering.
Acknowledgements: This investigation was supported by Serbian Ministry of Science and Education and it was conducted under following projects: 172057 and 45008.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts",
title = "Evaluation of Fly Ash Pysico-chemical Characteristics as Component for Eco-ceramic and Sintered Materials",
pages = "32-32",
url = "https://hdl.handle.net/21.15107/rcub_dais_532"
}

Terzić, A., Pavlović, L., Obradović, N., Pavlović, V. B., Radojević, Z., Miličić, L.,& Aćimović Pavlović, Z.. (2012). Evaluation of Fly Ash Pysico-chemical Characteristics as Component for Eco-ceramic and Sintered Materials. in The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts
Belgrade : Serbian Ceramic Society., 32-32.
https://hdl.handle.net/21.15107/rcub_dais_532

Terzić A, Pavlović L, Obradović N, Pavlović VB, Radojević Z, Miličić L, Aćimović Pavlović Z. Evaluation of Fly Ash Pysico-chemical Characteristics as Component for Eco-ceramic and Sintered Materials. in The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts. 2012;:32-32.
https://hdl.handle.net/21.15107/rcub_dais_532 .

Terzić, Anja, Pavlović, Ljubica, Obradović, Nina, Pavlović, Vladimir B., Radojević, Zagorka, Miličić, Ljiljana, Aćimović Pavlović, Zagorka, "Evaluation of Fly Ash Pysico-chemical Characteristics as Component for Eco-ceramic and Sintered Materials" in The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts (2012):32-32,
https://hdl.handle.net/21.15107/rcub_dais_532 .

TY  - JOUR
AU  - Obradović, N.
AU  - Terzić, Anja
AU  - Pavlović, Ljubica
AU  - Filipović, Suzana
AU  - Pavlović, Vladimir
PY  - 2012
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/3006
AB  - The base mix refractory concrete is corundum-based, containing corundum as refractory aggregate and CAC as hydraulic binder, with a spinel as an additive. The authors investigated the dehydration reactions which occur from the moment when water is added (at the beginning of components mixing), to the moment when installed refractory concrete lining is put into the service. Sintering process kinetic of low-cement content refractory concrete was investigated by means of differential thermal analysis at four different heating rates (5, 10, 20, and 30 A degrees C/min). Thus, temperature was increased from 20 to 1100 A degrees C. It was noticed that first dehydration step occurs at lower temperatures, indicating at a desorption of physically adsorbed and interlayer water molecules. Second dehydration step, at higher temperatures is due to dehydroxylation of the lattices and decomposition of the interlayer anions.
PB  - Springer, Dordrecht
T2  - Journal of Thermal Analysis and Calorimetry
T1  - Dehydration investigations of a refractory concrete using DTA method
EP  - 41
IS  - 1
SP  - 37
VL  - 110
DO  - 10.1007/s10973-011-1880-3
ER  - 

@article{
author = "Obradović, N. and Terzić, Anja and Pavlović, Ljubica and Filipović, Suzana and Pavlović, Vladimir",
year = "2012",
abstract = "The base mix refractory concrete is corundum-based, containing corundum as refractory aggregate and CAC as hydraulic binder, with a spinel as an additive. The authors investigated the dehydration reactions which occur from the moment when water is added (at the beginning of components mixing), to the moment when installed refractory concrete lining is put into the service. Sintering process kinetic of low-cement content refractory concrete was investigated by means of differential thermal analysis at four different heating rates (5, 10, 20, and 30 A degrees C/min). Thus, temperature was increased from 20 to 1100 A degrees C. It was noticed that first dehydration step occurs at lower temperatures, indicating at a desorption of physically adsorbed and interlayer water molecules. Second dehydration step, at higher temperatures is due to dehydroxylation of the lattices and decomposition of the interlayer anions.",
publisher = "Springer, Dordrecht",
journal = "Journal of Thermal Analysis and Calorimetry",
title = "Dehydration investigations of a refractory concrete using DTA method",
pages = "41-37",
number = "1",
volume = "110",
doi = "10.1007/s10973-011-1880-3"
}

Obradović, N., Terzić, A., Pavlović, L., Filipović, S.,& Pavlović, V.. (2012). Dehydration investigations of a refractory concrete using DTA method. in Journal of Thermal Analysis and Calorimetry
Springer, Dordrecht., 110(1), 37-41.
https://doi.org/10.1007/s10973-011-1880-3

Obradović N, Terzić A, Pavlović L, Filipović S, Pavlović V. Dehydration investigations of a refractory concrete using DTA method. in Journal of Thermal Analysis and Calorimetry. 2012;110(1):37-41.
doi:10.1007/s10973-011-1880-3 .

Obradović, N., Terzić, Anja, Pavlović, Ljubica, Filipović, Suzana, Pavlović, Vladimir, "Dehydration investigations of a refractory concrete using DTA method" in Journal of Thermal Analysis and Calorimetry, 110, no. 1 (2012):37-41,
https://doi.org/10.1007/s10973-011-1880-3 . .

TY  - CONF
AU  - Obradović, Nina
AU  - Terzić, Anja
AU  - Pavlović, Ljubica
AU  - Filipović, Suzana
AU  - Pavlović, Vladimir B.
PY  - 2011
UR  - http://dais.sanu.ac.rs/123456789/635
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5702
AB  - The base mix refractory concrete is corundum based, containing corundum as refractory aggregate and CAC as hydraulic binder, with spinel as an additive. The authors investigated the dehydration reactions which occur from the moment when water is added (at the beginning of components mixing), to the moment when installed refractory concrete lining is put into the service. Sintering process kinetic of low-cement content refractory concrete was investigated by means of differential thermal analysis (DTA) at three different heating rates (10, 20 and 30 •C/min). Thus, temperature was increased from 20 to 1100 •C. Activation energy during sintering process was determined by Kissinger method. Obtained values of activation energies were: 90.576 kJ/mol; 140.972 kJ/mol and 148.447 kJ/mol for TI, T2 and T3, respectively.
PB  - Craiova
C3  - Book of abstracts / CEEC-TACI : 1st Central and Eastern European Conference on Thermal Analysis and Calorimetry 7-10 September 2011, Craiova, Romania
T1  - Dehydration kinetics investigation of refractory concrete during sintering using DTA method
EP  - 45
SP  - 45
UR  - https://hdl.handle.net/21.15107/rcub_dais_635
ER  - 

@conference{
author = "Obradović, Nina and Terzić, Anja and Pavlović, Ljubica and Filipović, Suzana and Pavlović, Vladimir B.",
year = "2011",
abstract = "The base mix refractory concrete is corundum based, containing corundum as refractory aggregate and CAC as hydraulic binder, with spinel as an additive. The authors investigated the dehydration reactions which occur from the moment when water is added (at the beginning of components mixing), to the moment when installed refractory concrete lining is put into the service. Sintering process kinetic of low-cement content refractory concrete was investigated by means of differential thermal analysis (DTA) at three different heating rates (10, 20 and 30 •C/min). Thus, temperature was increased from 20 to 1100 •C. Activation energy during sintering process was determined by Kissinger method. Obtained values of activation energies were: 90.576 kJ/mol; 140.972 kJ/mol and 148.447 kJ/mol for TI, T2 and T3, respectively.",
publisher = "Craiova",
journal = "Book of abstracts / CEEC-TACI : 1st Central and Eastern European Conference on Thermal Analysis and Calorimetry 7-10 September 2011, Craiova, Romania",
title = "Dehydration kinetics investigation of refractory concrete during sintering using DTA method",
pages = "45-45",
url = "https://hdl.handle.net/21.15107/rcub_dais_635"
}

Obradović, N., Terzić, A., Pavlović, L., Filipović, S.,& Pavlović, V. B.. (2011). Dehydration kinetics investigation of refractory concrete during sintering using DTA method. in Book of abstracts / CEEC-TACI : 1st Central and Eastern European Conference on Thermal Analysis and Calorimetry 7-10 September 2011, Craiova, Romania
Craiova., 45-45.
https://hdl.handle.net/21.15107/rcub_dais_635

Obradović N, Terzić A, Pavlović L, Filipović S, Pavlović VB. Dehydration kinetics investigation of refractory concrete during sintering using DTA method. in Book of abstracts / CEEC-TACI : 1st Central and Eastern European Conference on Thermal Analysis and Calorimetry 7-10 September 2011, Craiova, Romania. 2011;:45-45.
https://hdl.handle.net/21.15107/rcub_dais_635 .

Obradović, Nina, Terzić, Anja, Pavlović, Ljubica, Filipović, Suzana, Pavlović, Vladimir B., "Dehydration kinetics investigation of refractory concrete during sintering using DTA method" in Book of abstracts / CEEC-TACI : 1st Central and Eastern European Conference on Thermal Analysis and Calorimetry 7-10 September 2011, Craiova, Romania (2011):45-45,
https://hdl.handle.net/21.15107/rcub_dais_635 .

TY  - CONF
AU  - Pavlović, MG
AU  - Popov, Konstantin I.
AU  - Krstić, Snežana B.
AU  - Pavlović, Ljubica
AU  - Ivanović, Evica
PY  - 2005
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/875
AB  - The surface structure of powder particles, which allows free flow of copper powder, was examined. It has been shown that a sufficiently dense surface structure which permits free flow will be obtained if apparent density is higher than 2.2 - 2.3 g/cm(3). Such a surface structure can be obtained by reversing current electrodeposition of powder at considerably lower apparent densities of powder due to selective dissolution of subparticles during anodic time of reversing current wave. The surface structure of copper powder particles is discussed and correlated with the lowest apparent density at which the copper powder can still flow.
PB  - 6th Conference of the Yugoslav Materials Research Society, YUCOMAT VI: Current Research in Advanced Materials and Processes
C3  - Materials Science Forum
T1  - Flowability of electrolytic copper powder
EP  - 252
SP  - 247
VL  - 494
DO  - 10.4028/0-87849-971-7.247
ER  - 

@conference{
author = "Pavlović, MG and Popov, Konstantin I. and Krstić, Snežana B. and Pavlović, Ljubica and Ivanović, Evica",
year = "2005",
abstract = "The surface structure of powder particles, which allows free flow of copper powder, was examined. It has been shown that a sufficiently dense surface structure which permits free flow will be obtained if apparent density is higher than 2.2 - 2.3 g/cm(3). Such a surface structure can be obtained by reversing current electrodeposition of powder at considerably lower apparent densities of powder due to selective dissolution of subparticles during anodic time of reversing current wave. The surface structure of copper powder particles is discussed and correlated with the lowest apparent density at which the copper powder can still flow.",
publisher = "6th Conference of the Yugoslav Materials Research Society, YUCOMAT VI: Current Research in Advanced Materials and Processes",
journal = "Materials Science Forum",
title = "Flowability of electrolytic copper powder",
pages = "252-247",
volume = "494",
doi = "10.4028/0-87849-971-7.247"
}

Pavlović, M., Popov, K. I., Krstić, S. B., Pavlović, L.,& Ivanović, E.. (2005). Flowability of electrolytic copper powder. in Materials Science Forum
6th Conference of the Yugoslav Materials Research Society, YUCOMAT VI: Current Research in Advanced Materials and Processes., 494, 247-252.
https://doi.org/10.4028/0-87849-971-7.247

Pavlović M, Popov KI, Krstić SB, Pavlović L, Ivanović E. Flowability of electrolytic copper powder. in Materials Science Forum. 2005;494:247-252.
doi:10.4028/0-87849-971-7.247 .

Pavlović, MG, Popov, Konstantin I., Krstić, Snežana B., Pavlović, Ljubica, Ivanović, Evica, "Flowability of electrolytic copper powder" in Materials Science Forum, 494 (2005):247-252,
https://doi.org/10.4028/0-87849-971-7.247 . .

TY  - CONF
AU  - Popov, Konstantin I.
AU  - Pavlović, MG
AU  - Pavlović, Ljubica
AU  - Maksimović, VM
AU  - Ivanović, Evica
PY  - 2004
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/805
AB  - The apparent density and flowability of copper powder are related to the structure of powder particles and the reversing current (RC) regimes. It was shown that the apparent density of the powders increases with the increase in the compactness of particles, hence with the increase in the frequency of RC and with the decrease in the cathodic to anodic time ratio.
PB  - Trans Tech Publications Ltd, Durnten-Zurich
C3  - Progress in Advanced Materials and Processes
T1  - The effect of reversing current on the properties of copper and electrolytic copper powder II. The apparent density and flowability of powders
EP  - 404
SP  - 399
VL  - 453-454
DO  - 10.4028/www.scientific.net/MSF.453-454.399
ER  - 

@conference{
author = "Popov, Konstantin I. and Pavlović, MG and Pavlović, Ljubica and Maksimović, VM and Ivanović, Evica",
year = "2004",
abstract = "The apparent density and flowability of copper powder are related to the structure of powder particles and the reversing current (RC) regimes. It was shown that the apparent density of the powders increases with the increase in the compactness of particles, hence with the increase in the frequency of RC and with the decrease in the cathodic to anodic time ratio.",
publisher = "Trans Tech Publications Ltd, Durnten-Zurich",
journal = "Progress in Advanced Materials and Processes",
title = "The effect of reversing current on the properties of copper and electrolytic copper powder II. The apparent density and flowability of powders",
pages = "404-399",
volume = "453-454",
doi = "10.4028/www.scientific.net/MSF.453-454.399"
}

Popov, K. I., Pavlović, M., Pavlović, L., Maksimović, V.,& Ivanović, E.. (2004). The effect of reversing current on the properties of copper and electrolytic copper powder II. The apparent density and flowability of powders. in Progress in Advanced Materials and Processes
Trans Tech Publications Ltd, Durnten-Zurich., 453-454, 399-404.
https://doi.org/10.4028/www.scientific.net/MSF.453-454.399

Popov KI, Pavlović M, Pavlović L, Maksimović V, Ivanović E. The effect of reversing current on the properties of copper and electrolytic copper powder II. The apparent density and flowability of powders. in Progress in Advanced Materials and Processes. 2004;453-454:399-404.
doi:10.4028/www.scientific.net/MSF.453-454.399 .

Popov, Konstantin I., Pavlović, MG, Pavlović, Ljubica, Maksimović, VM, Ivanović, Evica, "The effect of reversing current on the properties of copper and electrolytic copper powder II. The apparent density and flowability of powders" in Progress in Advanced Materials and Processes, 453-454 (2004):399-404,
https://doi.org/10.4028/www.scientific.net/MSF.453-454.399 . .

TY  - JOUR
AU  - Popov, Konstantin I.
AU  - Krstić, Snežana B.
AU  - Obradović, Milutin Č.
AU  - Pavlović, Miomir G.
AU  - Pavlović, Ljubica
AU  - Ivanović, Evica
PY  - 2004
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/817
AB  - The structure of the surface of copper powder particles is discussed and correlated with the lowest apparent density at which copper powder can still flow. It is shown that such structures can be easily obtained in the electrodeposition of powders in reversing current regimes.
AB  - Razmatrana je struktura površine čestica bakarnog praha i korelisana s najmanjom nasipnom masom pri kojoj bakarni prah još uvek može da teče. Pokazano je da se takva struktura može lako dobiti elektrohemijskim taloženjem praha u režimu reversne struje.
PB  - Srpsko hemijsko društvo, Beograd
T2  - JOURNAL OF THE SERBIAN CHEMICAL SOCIETY
T1  - The effect of the particle shape and structure on the flowability of electrolytic copper powder, III: A model of the surface of a representative particle of flowing copper powder electrodeposited by reversing current
T1  - Uticaj oblika I strukture čestica na tečljivost elektrolitičkog bakarnog praha III - model površine reprezentativne čestice tečljivog bakarnog praha dobijenog elektohemijskim taloženjem reversnom strujom
EP  - 51
IS  - 1
SP  - 43
VL  - 69
DO  - 10.2298/JSC0401043P
ER  - 

@article{
author = "Popov, Konstantin I. and Krstić, Snežana B. and Obradović, Milutin Č. and Pavlović, Miomir G. and Pavlović, Ljubica and Ivanović, Evica",
year = "2004",
abstract = "The structure of the surface of copper powder particles is discussed and correlated with the lowest apparent density at which copper powder can still flow. It is shown that such structures can be easily obtained in the electrodeposition of powders in reversing current regimes., Razmatrana je struktura površine čestica bakarnog praha i korelisana s najmanjom nasipnom masom pri kojoj bakarni prah još uvek može da teče. Pokazano je da se takva struktura može lako dobiti elektrohemijskim taloženjem praha u režimu reversne struje.",
publisher = "Srpsko hemijsko društvo, Beograd",
journal = "JOURNAL OF THE SERBIAN CHEMICAL SOCIETY",
title = "The effect of the particle shape and structure on the flowability of electrolytic copper powder, III: A model of the surface of a representative particle of flowing copper powder electrodeposited by reversing current, Uticaj oblika I strukture čestica na tečljivost elektrolitičkog bakarnog praha III - model površine reprezentativne čestice tečljivog bakarnog praha dobijenog elektohemijskim taloženjem reversnom strujom",
pages = "51-43",
number = "1",
volume = "69",
doi = "10.2298/JSC0401043P"
}

Popov, K. I., Krstić, S. B., Obradović, M. Č., Pavlović, M. G., Pavlović, L.,& Ivanović, E.. (2004). The effect of the particle shape and structure on the flowability of electrolytic copper powder, III: A model of the surface of a representative particle of flowing copper powder electrodeposited by reversing current. in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY
Srpsko hemijsko društvo, Beograd., 69(1), 43-51.
https://doi.org/10.2298/JSC0401043P

Popov KI, Krstić SB, Obradović MČ, Pavlović MG, Pavlović L, Ivanović E. The effect of the particle shape and structure on the flowability of electrolytic copper powder, III: A model of the surface of a representative particle of flowing copper powder electrodeposited by reversing current. in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY. 2004;69(1):43-51.
doi:10.2298/JSC0401043P .

Popov, Konstantin I., Krstić, Snežana B., Obradović, Milutin Č., Pavlović, Miomir G., Pavlović, Ljubica, Ivanović, Evica, "The effect of the particle shape and structure on the flowability of electrolytic copper powder, III: A model of the surface of a representative particle of flowing copper powder electrodeposited by reversing current" in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY, 69, no. 1 (2004):43-51,
https://doi.org/10.2298/JSC0401043P . .

TY  - CONF
AU  - Pavlović, MG
AU  - Popov, Konstantin I.
AU  - Pavlović, Ljubica
AU  - Ivanović, Evica
AU  - Jović, VD
PY  - 2004
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/813
AB  - The selective dissolution of copper dendrites during electrodeposition by reversing current was discussed and the effects on the morphology of copper powder particles were elucidated.
PB  - Trans Tech Publications Ltd, Durnten-Zurich
C3  - Progress in Advanced Materials and Processes
T1  - The effect of reversing current on the properties of copper and electrolytic copper powder. I. The morphology of powder particles
EP  - 398
SP  - 393
VL  - 453-454
DO  - 10.4028/www.scientific.net/MSF.453-454.393
ER  - 

@conference{
author = "Pavlović, MG and Popov, Konstantin I. and Pavlović, Ljubica and Ivanović, Evica and Jović, VD",
year = "2004",
abstract = "The selective dissolution of copper dendrites during electrodeposition by reversing current was discussed and the effects on the morphology of copper powder particles were elucidated.",
publisher = "Trans Tech Publications Ltd, Durnten-Zurich",
journal = "Progress in Advanced Materials and Processes",
title = "The effect of reversing current on the properties of copper and electrolytic copper powder. I. The morphology of powder particles",
pages = "398-393",
volume = "453-454",
doi = "10.4028/www.scientific.net/MSF.453-454.393"
}

Pavlović, M., Popov, K. I., Pavlović, L., Ivanović, E.,& Jović, V.. (2004). The effect of reversing current on the properties of copper and electrolytic copper powder. I. The morphology of powder particles. in Progress in Advanced Materials and Processes
Trans Tech Publications Ltd, Durnten-Zurich., 453-454, 393-398.
https://doi.org/10.4028/www.scientific.net/MSF.453-454.393

Pavlović M, Popov KI, Pavlović L, Ivanović E, Jović V. The effect of reversing current on the properties of copper and electrolytic copper powder. I. The morphology of powder particles. in Progress in Advanced Materials and Processes. 2004;453-454:393-398.
doi:10.4028/www.scientific.net/MSF.453-454.393 .

Pavlović, MG, Popov, Konstantin I., Pavlović, Ljubica, Ivanović, Evica, Jović, VD, "The effect of reversing current on the properties of copper and electrolytic copper powder. I. The morphology of powder particles" in Progress in Advanced Materials and Processes, 453-454 (2004):393-398,
https://doi.org/10.4028/www.scientific.net/MSF.453-454.393 . .

TY  - JOUR
AU  - Popov, Konstantin I.
AU  - Pavlović, Miomir G.
AU  - Pavlović, Ljubica
AU  - Ivanović, Evica
AU  - Krstić, Snežana B.
AU  - Obradović, Milutin Č.
PY  - 2003
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/598
AB  - An analysis of the effects of the shape, surface structure and size distribution of particles on the flow ability of the copper powder was performed. It is shown that the most important property of the particles of a powder, regarding the flow ability of the powder, is the surface structure of the particles.
AB  - Izvedena je analiza uticaja oblika, površinske strukture i raspodele veličina čestica na tečljivost bakarnog praha. Pokazano je da površinska struktura predstavlja najvažnije svojstvo čestice praha u odnosu na njegovu tečljivost.
PB  - Srpsko hemijsko društvo, Beograd
T2  - JOURNAL OF THE SERBIAN CHEMICAL SOCIETY
T1  - The effect of the particle shape and structure on the flow ability of electrolytic copper powder II: The experimental verification of the model of the representative powder particle
T1  - Uticaj oblika i strukture čestica na tečljivost elektrolitičkog bakarnog praha II - eksperimentalna potvrda modela reprezentativne čestice praha
EP  - 783
IS  - 10
SP  - 779
VL  - 68
DO  - 10.2298/JSC0310779P
ER  - 

@article{
author = "Popov, Konstantin I. and Pavlović, Miomir G. and Pavlović, Ljubica and Ivanović, Evica and Krstić, Snežana B. and Obradović, Milutin Č.",
year = "2003",
abstract = "An analysis of the effects of the shape, surface structure and size distribution of particles on the flow ability of the copper powder was performed. It is shown that the most important property of the particles of a powder, regarding the flow ability of the powder, is the surface structure of the particles., Izvedena je analiza uticaja oblika, površinske strukture i raspodele veličina čestica na tečljivost bakarnog praha. Pokazano je da površinska struktura predstavlja najvažnije svojstvo čestice praha u odnosu na njegovu tečljivost.",
publisher = "Srpsko hemijsko društvo, Beograd",
journal = "JOURNAL OF THE SERBIAN CHEMICAL SOCIETY",
title = "The effect of the particle shape and structure on the flow ability of electrolytic copper powder II: The experimental verification of the model of the representative powder particle, Uticaj oblika i strukture čestica na tečljivost elektrolitičkog bakarnog praha II - eksperimentalna potvrda modela reprezentativne čestice praha",
pages = "783-779",
number = "10",
volume = "68",
doi = "10.2298/JSC0310779P"
}

Popov, K. I., Pavlović, M. G., Pavlović, L., Ivanović, E., Krstić, S. B.,& Obradović, M. Č.. (2003). The effect of the particle shape and structure on the flow ability of electrolytic copper powder II: The experimental verification of the model of the representative powder particle. in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY
Srpsko hemijsko društvo, Beograd., 68(10), 779-783.
https://doi.org/10.2298/JSC0310779P

Popov KI, Pavlović MG, Pavlović L, Ivanović E, Krstić SB, Obradović MČ. The effect of the particle shape and structure on the flow ability of electrolytic copper powder II: The experimental verification of the model of the representative powder particle. in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY. 2003;68(10):779-783.
doi:10.2298/JSC0310779P .

Popov, Konstantin I., Pavlović, Miomir G., Pavlović, Ljubica, Ivanović, Evica, Krstić, Snežana B., Obradović, Milutin Č., "The effect of the particle shape and structure on the flow ability of electrolytic copper powder II: The experimental verification of the model of the representative powder particle" in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY, 68, no. 10 (2003):779-783,
https://doi.org/10.2298/JSC0310779P . .

TY  - JOUR
AU  - Popov, Konstantin I.
AU  - Krstić, Snežana B.
AU  - Obradović, Milutin Č.
AU  - Pavlović, Miomir G.
AU  - Pavlović, Ljubica
AU  - Ivanović, Evica
PY  - 2003
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/649
AB  - One of the most important properties of copper powder is its flow ability which depends on the shape and the structure of the powder particles. A procedure for the determination of a representative powder particle permitting the free flow of copper powder is proposed.
AB  - Jedno od najvažnijih svojstava bakarnog praha je njegova tečljivost, koja zavisi od oblika i strukture čestica praha. Predložen je postupak za određivanje reprezentativne čestice praha koja obezbeđuje slobodno tečenje bakarnog praha.
PB  - Srpsko hemijsko društvo, Beograd
T2  - Journal of the Serbian Chemical Society
T1  - The effect of the particle shape and structure on the flowability of electrolytic copper powder I: Modeling of a representative powder particle
T1  - Uticaj oblika i strukture čestica na tečljivost elektrolitičkog bakarnog praha I - modelovanje reprezentativne čestice praha
EP  - 778
IS  - 10
SP  - 771
VL  - 68
UR  - https://hdl.handle.net/21.15107/rcub_agrospace_649
ER  - 

@article{
author = "Popov, Konstantin I. and Krstić, Snežana B. and Obradović, Milutin Č. and Pavlović, Miomir G. and Pavlović, Ljubica and Ivanović, Evica",
year = "2003",
abstract = "One of the most important properties of copper powder is its flow ability which depends on the shape and the structure of the powder particles. A procedure for the determination of a representative powder particle permitting the free flow of copper powder is proposed., Jedno od najvažnijih svojstava bakarnog praha je njegova tečljivost, koja zavisi od oblika i strukture čestica praha. Predložen je postupak za određivanje reprezentativne čestice praha koja obezbeđuje slobodno tečenje bakarnog praha.",
publisher = "Srpsko hemijsko društvo, Beograd",
journal = "Journal of the Serbian Chemical Society",
title = "The effect of the particle shape and structure on the flowability of electrolytic copper powder I: Modeling of a representative powder particle, Uticaj oblika i strukture čestica na tečljivost elektrolitičkog bakarnog praha I - modelovanje reprezentativne čestice praha",
pages = "778-771",
number = "10",
volume = "68",
url = "https://hdl.handle.net/21.15107/rcub_agrospace_649"
}

Popov, K. I., Krstić, S. B., Obradović, M. Č., Pavlović, M. G., Pavlović, L.,& Ivanović, E.. (2003). The effect of the particle shape and structure on the flowability of electrolytic copper powder I: Modeling of a representative powder particle. in Journal of the Serbian Chemical Society
Srpsko hemijsko društvo, Beograd., 68(10), 771-778.
https://hdl.handle.net/21.15107/rcub_agrospace_649

Popov KI, Krstić SB, Obradović MČ, Pavlović MG, Pavlović L, Ivanović E. The effect of the particle shape and structure on the flowability of electrolytic copper powder I: Modeling of a representative powder particle. in Journal of the Serbian Chemical Society. 2003;68(10):771-778.
https://hdl.handle.net/21.15107/rcub_agrospace_649 .

Popov, Konstantin I., Krstić, Snežana B., Obradović, Milutin Č., Pavlović, Miomir G., Pavlović, Ljubica, Ivanović, Evica, "The effect of the particle shape and structure on the flowability of electrolytic copper powder I: Modeling of a representative powder particle" in Journal of the Serbian Chemical Society, 68, no. 10 (2003):771-778,
https://hdl.handle.net/21.15107/rcub_agrospace_649 .

TY  - JOUR
AU  - Popov, Konstantin I.
AU  - Krstić, Snežana B.
AU  - Obradović, MC
AU  - Pavlović, MG
AU  - Pavlović, Ljubica
AU  - Ivanović, Evica
PY  - 2003
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/605
AB  - One of the most important properties of copper powder is its flowability which depends on the shape and the structure of the powder particles. A procedure for the determination of a representative powder particle permitting the free flow of copper powder is proposed.
PB  - Srpsko hemijsko društvo, Beograd
T2  - JOURNAL OF THE SERBIAN CHEMICAL SOCIETY
T1  - The effect of the particle shape and structure on the flowability of electrolytic copper powder. I. Modeling of a representative powder particle
EP  - 777
IS  - 10
SP  - 771
VL  - 68
DO  - 10.2298/JSC0310771P
ER  - 

@article{
author = "Popov, Konstantin I. and Krstić, Snežana B. and Obradović, MC and Pavlović, MG and Pavlović, Ljubica and Ivanović, Evica",
year = "2003",
abstract = "One of the most important properties of copper powder is its flowability which depends on the shape and the structure of the powder particles. A procedure for the determination of a representative powder particle permitting the free flow of copper powder is proposed.",
publisher = "Srpsko hemijsko društvo, Beograd",
journal = "JOURNAL OF THE SERBIAN CHEMICAL SOCIETY",
title = "The effect of the particle shape and structure on the flowability of electrolytic copper powder. I. Modeling of a representative powder particle",
pages = "777-771",
number = "10",
volume = "68",
doi = "10.2298/JSC0310771P"
}

Popov, K. I., Krstić, S. B., Obradović, M., Pavlović, M., Pavlović, L.,& Ivanović, E.. (2003). The effect of the particle shape and structure on the flowability of electrolytic copper powder. I. Modeling of a representative powder particle. in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY
Srpsko hemijsko društvo, Beograd., 68(10), 771-777.
https://doi.org/10.2298/JSC0310771P

Popov KI, Krstić SB, Obradović M, Pavlović M, Pavlović L, Ivanović E. The effect of the particle shape and structure on the flowability of electrolytic copper powder. I. Modeling of a representative powder particle. in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY. 2003;68(10):771-777.
doi:10.2298/JSC0310771P .

Popov, Konstantin I., Krstić, Snežana B., Obradović, MC, Pavlović, MG, Pavlović, Ljubica, Ivanović, Evica, "The effect of the particle shape and structure on the flowability of electrolytic copper powder. I. Modeling of a representative powder particle" in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY, 68, no. 10 (2003):771-777,
https://doi.org/10.2298/JSC0310771P . .

TY  - JOUR
AU  - Popov, Konstantin I.
AU  - Pavlović, Ljubica
AU  - Ivanović, Evica
AU  - Radmilović, Velimir R.
AU  - Pavlović, Miomir G.
PY  - 2002
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/521
AB  - The possibility of depositing copper powders with different apparent density by changing the shape of reversing current wave is shown. The morphology and crystallinity of powder particles can be varied considerably by changing shape of the reversing current wave and, hence, the apparent density of powders. The relation of apparent density with particle morphology and structure was illustrated.
AB  - U radu je pokazana mogućnost dobijanja bakarnih prahova različitih nasipnih masa promenom oblika talasa reversne struje. Uspostavljena je zadovoljavajuća veza između morfologije i strukture čestica praha bakra i nasipne mase praha.
PB  - Srpsko hemijsko društvo, Beograd
T2  - JOURNAL OF THE SERBIAN CHEMICAL SOCIETY
T1  - The effect of reversing current deposition on the apparent density of electrolytic copper powder
T1  - Uticaj reversne struje na nasipnu masu pri elektrolitičkom taloženju bakarnog praha
EP  - 67
IS  - 1
SP  - 61
VL  - 67
DO  - 10.2298/JSC0201061P
ER  - 

@article{
author = "Popov, Konstantin I. and Pavlović, Ljubica and Ivanović, Evica and Radmilović, Velimir R. and Pavlović, Miomir G.",
year = "2002",
abstract = "The possibility of depositing copper powders with different apparent density by changing the shape of reversing current wave is shown. The morphology and crystallinity of powder particles can be varied considerably by changing shape of the reversing current wave and, hence, the apparent density of powders. The relation of apparent density with particle morphology and structure was illustrated., U radu je pokazana mogućnost dobijanja bakarnih prahova različitih nasipnih masa promenom oblika talasa reversne struje. Uspostavljena je zadovoljavajuća veza između morfologije i strukture čestica praha bakra i nasipne mase praha.",
publisher = "Srpsko hemijsko društvo, Beograd",
journal = "JOURNAL OF THE SERBIAN CHEMICAL SOCIETY",
title = "The effect of reversing current deposition on the apparent density of electrolytic copper powder, Uticaj reversne struje na nasipnu masu pri elektrolitičkom taloženju bakarnog praha",
pages = "67-61",
number = "1",
volume = "67",
doi = "10.2298/JSC0201061P"
}

Popov, K. I., Pavlović, L., Ivanović, E., Radmilović, V. R.,& Pavlović, M. G.. (2002). The effect of reversing current deposition on the apparent density of electrolytic copper powder. in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY
Srpsko hemijsko društvo, Beograd., 67(1), 61-67.
https://doi.org/10.2298/JSC0201061P

Popov KI, Pavlović L, Ivanović E, Radmilović VR, Pavlović MG. The effect of reversing current deposition on the apparent density of electrolytic copper powder. in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY. 2002;67(1):61-67.
doi:10.2298/JSC0201061P .

Popov, Konstantin I., Pavlović, Ljubica, Ivanović, Evica, Radmilović, Velimir R., Pavlović, Miomir G., "The effect of reversing current deposition on the apparent density of electrolytic copper powder" in JOURNAL OF THE SERBIAN CHEMICAL SOCIETY, 67, no. 1 (2002):61-67,
https://doi.org/10.2298/JSC0201061P . .

TY  - JOUR
AU  - Pavlović, M.G.
AU  - Pavlović, Ljubica
AU  - Ivanović, Evica
AU  - Radmilović, V.
AU  - Popov, Konstantin I.
PY  - 2001
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/280
AB  - The quantitative microstructural analysis and the sieve analysis of copper powder as well as the scanning electron microscopy analysis of the copper powders particles were performed. It was found that the structure of the copper powder particles determines the apparent density of copper powder. The powder particles from the same fractions of different powders occupy approximately the same volume, but the structure of metallic copper is very different. This causes the difference in apparent densities of copper powder obtained under different conditions. The more dendritic is the structure of powder particles the smaller is the apparent density of copper powder.
AB  - Izvršena je kvalitativna mikrostrukturna i granulometrijska analiza bakarnih prahova kao i analiza morfologije i strukture čestica praha pomoću skenirajuće elektronske mikroskopije (SEM). Ustanovljeno je da struktura čestica praha određuje nasipnu masu bakarnog praha. Čestice iste frakcije različitih prahova zauzimaju otprilike istu zapreminu, ali je struktura metalnog bakra različita. Ovo uzrokuje razlike u nasipnoj masi bakarnog praha dobijenog pod različitim uslovima. Što je struktura čestica više dendritična to je manja nasipna masa bakarnog praha.
PB  - Srpsko hemijsko društvo, Beograd
T2  - Journal of the Serbian Chemical Society
T1  - The effect of particle structure on apparent density of electrolytic copper powder
T1  - Uticaj strukture čestica na nasipnu masu elektrolitički dobijenog bakarnog praha
EP  - 933
IS  - 11-12
SP  - 923
VL  - 66
DO  - 10.2298/jsc0112923p
ER  - 

@article{
author = "Pavlović, M.G. and Pavlović, Ljubica and Ivanović, Evica and Radmilović, V. and Popov, Konstantin I.",
year = "2001",
abstract = "The quantitative microstructural analysis and the sieve analysis of copper powder as well as the scanning electron microscopy analysis of the copper powders particles were performed. It was found that the structure of the copper powder particles determines the apparent density of copper powder. The powder particles from the same fractions of different powders occupy approximately the same volume, but the structure of metallic copper is very different. This causes the difference in apparent densities of copper powder obtained under different conditions. The more dendritic is the structure of powder particles the smaller is the apparent density of copper powder., Izvršena je kvalitativna mikrostrukturna i granulometrijska analiza bakarnih prahova kao i analiza morfologije i strukture čestica praha pomoću skenirajuće elektronske mikroskopije (SEM). Ustanovljeno je da struktura čestica praha određuje nasipnu masu bakarnog praha. Čestice iste frakcije različitih prahova zauzimaju otprilike istu zapreminu, ali je struktura metalnog bakra različita. Ovo uzrokuje razlike u nasipnoj masi bakarnog praha dobijenog pod različitim uslovima. Što je struktura čestica više dendritična to je manja nasipna masa bakarnog praha.",
publisher = "Srpsko hemijsko društvo, Beograd",
journal = "Journal of the Serbian Chemical Society",
title = "The effect of particle structure on apparent density of electrolytic copper powder, Uticaj strukture čestica na nasipnu masu elektrolitički dobijenog bakarnog praha",
pages = "933-923",
number = "11-12",
volume = "66",
doi = "10.2298/jsc0112923p"
}

Pavlović, M.G., Pavlović, L., Ivanović, E., Radmilović, V.,& Popov, K. I.. (2001). The effect of particle structure on apparent density of electrolytic copper powder. in Journal of the Serbian Chemical Society
Srpsko hemijsko društvo, Beograd., 66(11-12), 923-933.
https://doi.org/10.2298/jsc0112923p

Pavlović M, Pavlović L, Ivanović E, Radmilović V, Popov KI. The effect of particle structure on apparent density of electrolytic copper powder. in Journal of the Serbian Chemical Society. 2001;66(11-12):923-933.
doi:10.2298/jsc0112923p .

Pavlović, M.G., Pavlović, Ljubica, Ivanović, Evica, Radmilović, V., Popov, Konstantin I., "The effect of particle structure on apparent density of electrolytic copper powder" in Journal of the Serbian Chemical Society, 66, no. 11-12 (2001):923-933,
https://doi.org/10.2298/jsc0112923p . .