TY  - JOUR
AU  - Obradović, Nina
AU  - Fahrenholtz, William G.
AU  - Filipović, Suzana
AU  - Marković, Smilja
AU  - Blagojević, Vladimir A.
AU  - Lević, Steva
AU  - Savić, Slobodan
AU  - Djordjević, Antonije
AU  - Pavlović, Vladimir
PY  - 2020
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5344
AB  - Solid-state mechanical activation of MgO and alpha-Al2O3 powders was used to produce MgAl2O4. The cation site occupancy in the resulting MgAl2O4 spinel was investigated using different methods. Differential thermal analysis and thermal gravimetry showed that mechanical activation reduced the spinel formation temperature by around 200 degrees C, and the corresponding activation energy by about 25%. In addition, characteristic temperatures for evaporation of physisorbed water and decomposition of Mg(OH)(2) shifted to lower values, and peaks were more pronounced. Raman spectra were used to characterize the degree of inversion as a function of the sintering temperature for all of the sintered specimens, indicating that the breaking point for ordering of the crystal structure was around 1500 degrees C for non-activated samples, and 1400 degrees C for activated samples.
PB  - Springer, Dordrecht
T2  - Journal of Thermal Analysis and Calorimetry
T1  - Formation kinetics and cation inversion in mechanically activated MgAl2O4 spinel ceramics
EP  - 107
IS  - 1
SP  - 95
VL  - 140
DO  - 10.1007/s10973-019-08846-w
ER  - 

@article{
author = "Obradović, Nina and Fahrenholtz, William G. and Filipović, Suzana and Marković, Smilja and Blagojević, Vladimir A. and Lević, Steva and Savić, Slobodan and Djordjević, Antonije and Pavlović, Vladimir",
year = "2020",
abstract = "Solid-state mechanical activation of MgO and alpha-Al2O3 powders was used to produce MgAl2O4. The cation site occupancy in the resulting MgAl2O4 spinel was investigated using different methods. Differential thermal analysis and thermal gravimetry showed that mechanical activation reduced the spinel formation temperature by around 200 degrees C, and the corresponding activation energy by about 25%. In addition, characteristic temperatures for evaporation of physisorbed water and decomposition of Mg(OH)(2) shifted to lower values, and peaks were more pronounced. Raman spectra were used to characterize the degree of inversion as a function of the sintering temperature for all of the sintered specimens, indicating that the breaking point for ordering of the crystal structure was around 1500 degrees C for non-activated samples, and 1400 degrees C for activated samples.",
publisher = "Springer, Dordrecht",
journal = "Journal of Thermal Analysis and Calorimetry",
title = "Formation kinetics and cation inversion in mechanically activated MgAl2O4 spinel ceramics",
pages = "107-95",
number = "1",
volume = "140",
doi = "10.1007/s10973-019-08846-w"
}

Obradović, N., Fahrenholtz, W. G., Filipović, S., Marković, S., Blagojević, V. A., Lević, S., Savić, S., Djordjević, A.,& Pavlović, V.. (2020). Formation kinetics and cation inversion in mechanically activated MgAl2O4 spinel ceramics. in Journal of Thermal Analysis and Calorimetry
Springer, Dordrecht., 140(1), 95-107.
https://doi.org/10.1007/s10973-019-08846-w

Obradović N, Fahrenholtz WG, Filipović S, Marković S, Blagojević VA, Lević S, Savić S, Djordjević A, Pavlović V. Formation kinetics and cation inversion in mechanically activated MgAl2O4 spinel ceramics. in Journal of Thermal Analysis and Calorimetry. 2020;140(1):95-107.
doi:10.1007/s10973-019-08846-w .

Obradović, Nina, Fahrenholtz, William G., Filipović, Suzana, Marković, Smilja, Blagojević, Vladimir A., Lević, Steva, Savić, Slobodan, Djordjević, Antonije, Pavlović, Vladimir, "Formation kinetics and cation inversion in mechanically activated MgAl2O4 spinel ceramics" in Journal of Thermal Analysis and Calorimetry, 140, no. 1 (2020):95-107,
https://doi.org/10.1007/s10973-019-08846-w . .

TY  - JOUR
AU  - Obradović, Nina
AU  - Pavlović, Vera P.
AU  - Kachlik, Martin
AU  - Maca, Karel
AU  - Olcan, Dragan
AU  - Djordjević, Antonije
AU  - Tshantshapanyan, Ani
AU  - Vlahović, Branislav
AU  - Pavlović, Vladimir
PY  - 2019
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5098
AB  - Sintering of pure cordierite 2MgO:2Al(2)O(3):5SiO(2), and cordierite with the addition of 5 mass % TeO2 was studied. Green bodies were prepared from powder mixtures mechanically activated in a high-energy planetary mill, shaped by uniaxial (20 MPa) and cold isostatic pressing (1000 MPa). The pressure-less sintering of these specimens was performed at 1350 degrees C for 1 h. High relative density over 95% of the theoretical value was obtained through solid-state reaction and pressure-less sintering of powder activated for 40 min, and for the first time reported in the literature. Phase composition and microstructures of sintered samples were determined by XRD and SEM, coupled with EDS mapping. The real part of the complex relative permittivity of the samples was measured at 200 MHz. The loss tangent of all samples was below the resolution of the measurement setup. A strong correlation between the relative permittivity and the density agrees with previously published data.
PB  - Taylor & Francis Ltd, Abingdon
T2  - Advances in Applied Ceramics
T1  - Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering
EP  - 248
IS  - 5
SP  - 241
VL  - 118
DO  - 10.1080/17436753.2018.1548150
ER  - 

@article{
author = "Obradović, Nina and Pavlović, Vera P. and Kachlik, Martin and Maca, Karel and Olcan, Dragan and Djordjević, Antonije and Tshantshapanyan, Ani and Vlahović, Branislav and Pavlović, Vladimir",
year = "2019",
abstract = "Sintering of pure cordierite 2MgO:2Al(2)O(3):5SiO(2), and cordierite with the addition of 5 mass % TeO2 was studied. Green bodies were prepared from powder mixtures mechanically activated in a high-energy planetary mill, shaped by uniaxial (20 MPa) and cold isostatic pressing (1000 MPa). The pressure-less sintering of these specimens was performed at 1350 degrees C for 1 h. High relative density over 95% of the theoretical value was obtained through solid-state reaction and pressure-less sintering of powder activated for 40 min, and for the first time reported in the literature. Phase composition and microstructures of sintered samples were determined by XRD and SEM, coupled with EDS mapping. The real part of the complex relative permittivity of the samples was measured at 200 MHz. The loss tangent of all samples was below the resolution of the measurement setup. A strong correlation between the relative permittivity and the density agrees with previously published data.",
publisher = "Taylor & Francis Ltd, Abingdon",
journal = "Advances in Applied Ceramics",
title = "Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering",
pages = "248-241",
number = "5",
volume = "118",
doi = "10.1080/17436753.2018.1548150"
}

Obradović, N., Pavlović, V. P., Kachlik, M., Maca, K., Olcan, D., Djordjević, A., Tshantshapanyan, A., Vlahović, B.,& Pavlović, V.. (2019). Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering. in Advances in Applied Ceramics
Taylor & Francis Ltd, Abingdon., 118(5), 241-248.
https://doi.org/10.1080/17436753.2018.1548150

Obradović N, Pavlović VP, Kachlik M, Maca K, Olcan D, Djordjević A, Tshantshapanyan A, Vlahović B, Pavlović V. Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering. in Advances in Applied Ceramics. 2019;118(5):241-248.
doi:10.1080/17436753.2018.1548150 .

Obradović, Nina, Pavlović, Vera P., Kachlik, Martin, Maca, Karel, Olcan, Dragan, Djordjević, Antonije, Tshantshapanyan, Ani, Vlahović, Branislav, Pavlović, Vladimir, "Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering" in Advances in Applied Ceramics, 118, no. 5 (2019):241-248,
https://doi.org/10.1080/17436753.2018.1548150 . .

TY  - JOUR
AU  - Rusmirović, Jelena D.
AU  - Obradović, Nina
AU  - Perendija, Jovana
AU  - Umićević, Ana B.
AU  - Kapidzić, Ana
AU  - Vlahović, Branislav
AU  - Pavlović, Vera P.
AU  - Marinković, Aleksandar D.
AU  - Pavlović, Vladimir
PY  - 2019
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5118
AB  - Iron oxide, in the form of magnetite (MG)-functionalized porous wollastonite (WL), was used as an adsorbent for heavy metal ions (cadmium and nickel) and oxyanions (chromate and phosphate) removal from water. The porous WL was synthesized from calcium carbonate and siloxane by controlled sintering process using low molecular weight submicrosized poly(methyl methacrylate) as a pore-forming agent. The precipitation of MG nanoparticles was carried out directly by a polyol-medium solvothermal method or via branched amino/carboxylic acid cross-linker by solvent/nonsolvent method producing WL/MG and WL--APS/MG adsorbents, respectively. The structure/properties of MG functionalized WL was confirmed by applying FTIR, Raman, XRD, Mossbauer, and SEM analysis. Higher adsorption capacities of 73.126, 66.144, 64.168, and 63.456mgg(-1) for WL--APS/MG in relation to WL/MG of 55.450, 52.019, 48.132, and 47.382mgg(-1) for Cd2+, Ni2+, phosphate, and chromate, respectively, were obtained using nonlinear Langmuir model fitting. Adsorption phenomena were analyzed using monolayer statistical physics model for single adsorption with one energy. Kinetic study showed exceptionally higher pseudo-second-order rate constants for WL--APS/MG, e.g., 1.17-13.4 times, with respect to WL/MG indicating importance of both WL surface modification and controllable precipitation of MG on WL--APS.
PB  - Springer Heidelberg, Heidelberg
T2  - Environmental Science and Pollution Research
T1  - Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal
EP  - 12398
IS  - 12
SP  - 12379
VL  - 26
DO  - 10.1007/s11356-019-04625-0
ER  - 

@article{
author = "Rusmirović, Jelena D. and Obradović, Nina and Perendija, Jovana and Umićević, Ana B. and Kapidzić, Ana and Vlahović, Branislav and Pavlović, Vera P. and Marinković, Aleksandar D. and Pavlović, Vladimir",
year = "2019",
abstract = "Iron oxide, in the form of magnetite (MG)-functionalized porous wollastonite (WL), was used as an adsorbent for heavy metal ions (cadmium and nickel) and oxyanions (chromate and phosphate) removal from water. The porous WL was synthesized from calcium carbonate and siloxane by controlled sintering process using low molecular weight submicrosized poly(methyl methacrylate) as a pore-forming agent. The precipitation of MG nanoparticles was carried out directly by a polyol-medium solvothermal method or via branched amino/carboxylic acid cross-linker by solvent/nonsolvent method producing WL/MG and WL--APS/MG adsorbents, respectively. The structure/properties of MG functionalized WL was confirmed by applying FTIR, Raman, XRD, Mossbauer, and SEM analysis. Higher adsorption capacities of 73.126, 66.144, 64.168, and 63.456mgg(-1) for WL--APS/MG in relation to WL/MG of 55.450, 52.019, 48.132, and 47.382mgg(-1) for Cd2+, Ni2+, phosphate, and chromate, respectively, were obtained using nonlinear Langmuir model fitting. Adsorption phenomena were analyzed using monolayer statistical physics model for single adsorption with one energy. Kinetic study showed exceptionally higher pseudo-second-order rate constants for WL--APS/MG, e.g., 1.17-13.4 times, with respect to WL/MG indicating importance of both WL surface modification and controllable precipitation of MG on WL--APS.",
publisher = "Springer Heidelberg, Heidelberg",
journal = "Environmental Science and Pollution Research",
title = "Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal",
pages = "12398-12379",
number = "12",
volume = "26",
doi = "10.1007/s11356-019-04625-0"
}

Rusmirović, J. D., Obradović, N., Perendija, J., Umićević, A. B., Kapidzić, A., Vlahović, B., Pavlović, V. P., Marinković, A. D.,& Pavlović, V.. (2019). Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal. in Environmental Science and Pollution Research
Springer Heidelberg, Heidelberg., 26(12), 12379-12398.
https://doi.org/10.1007/s11356-019-04625-0

Rusmirović JD, Obradović N, Perendija J, Umićević AB, Kapidzić A, Vlahović B, Pavlović VP, Marinković AD, Pavlović V. Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal. in Environmental Science and Pollution Research. 2019;26(12):12379-12398.
doi:10.1007/s11356-019-04625-0 .

Rusmirović, Jelena D., Obradović, Nina, Perendija, Jovana, Umićević, Ana B., Kapidzić, Ana, Vlahović, Branislav, Pavlović, Vera P., Marinković, Aleksandar D., Pavlović, Vladimir, "Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal" in Environmental Science and Pollution Research, 26, no. 12 (2019):12379-12398,
https://doi.org/10.1007/s11356-019-04625-0 . .

TY  - DATA
AU  - Rusmirović, Jelena
AU  - Obradović, Nina
AU  - Perendija, Jovana
AU  - Umićević, Ana
AU  - Kapidžić, Ana
AU  - Vlahović, Branislav
AU  - Pavlović, Vera P.
AU  - Marinković, Aleksandar D.
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - http://dais.sanu.ac.rs/123456789/5805
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5741
PB  - Springer
T2  - Environmental Science and Pollution Research
T1  - Supplementary material for the article: Rusmirović, J.D., Obradović, N., Perendija, J., Umićević, A., Kapidžić, A., Vlahović, B., Pavlović, V., Marinković, A.D., Pavlović, V.B., 2019. Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal. Environ Sci Pollut Res 26, 12379–12398. https://doi.org/10.1007/s11356-019-04625-0
UR  - https://hdl.handle.net/21.15107/rcub_dais_5805
ER  - 

@misc{
author = "Rusmirović, Jelena and Obradović, Nina and Perendija, Jovana and Umićević, Ana and Kapidžić, Ana and Vlahović, Branislav and Pavlović, Vera P. and Marinković, Aleksandar D. and Pavlović, Vladimir B.",
year = "2019",
publisher = "Springer",
journal = "Environmental Science and Pollution Research",
title = "Supplementary material for the article: Rusmirović, J.D., Obradović, N., Perendija, J., Umićević, A., Kapidžić, A., Vlahović, B., Pavlović, V., Marinković, A.D., Pavlović, V.B., 2019. Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal. Environ Sci Pollut Res 26, 12379–12398. https://doi.org/10.1007/s11356-019-04625-0",
url = "https://hdl.handle.net/21.15107/rcub_dais_5805"
}

Rusmirović, J., Obradović, N., Perendija, J., Umićević, A., Kapidžić, A., Vlahović, B., Pavlović, V. P., Marinković, A. D.,& Pavlović, V. B.. (2019). Supplementary material for the article: Rusmirović, J.D., Obradović, N., Perendija, J., Umićević, A., Kapidžić, A., Vlahović, B., Pavlović, V., Marinković, A.D., Pavlović, V.B., 2019. Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal. Environ Sci Pollut Res 26, 12379–12398. https://doi.org/10.1007/s11356-019-04625-0. in Environmental Science and Pollution Research
Springer..
https://hdl.handle.net/21.15107/rcub_dais_5805

Rusmirović J, Obradović N, Perendija J, Umićević A, Kapidžić A, Vlahović B, Pavlović VP, Marinković AD, Pavlović VB. Supplementary material for the article: Rusmirović, J.D., Obradović, N., Perendija, J., Umićević, A., Kapidžić, A., Vlahović, B., Pavlović, V., Marinković, A.D., Pavlović, V.B., 2019. Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal. Environ Sci Pollut Res 26, 12379–12398. https://doi.org/10.1007/s11356-019-04625-0. in Environmental Science and Pollution Research. 2019;.
https://hdl.handle.net/21.15107/rcub_dais_5805 .

Rusmirović, Jelena, Obradović, Nina, Perendija, Jovana, Umićević, Ana, Kapidžić, Ana, Vlahović, Branislav, Pavlović, Vera P., Marinković, Aleksandar D., Pavlović, Vladimir B., "Supplementary material for the article: Rusmirović, J.D., Obradović, N., Perendija, J., Umićević, A., Kapidžić, A., Vlahović, B., Pavlović, V., Marinković, A.D., Pavlović, V.B., 2019. Controllable synthesis of Fe3O4-wollastonite adsorbents for efficient heavy metal ions/oxyanions removal. Environ Sci Pollut Res 26, 12379–12398. https://doi.org/10.1007/s11356-019-04625-0" in Environmental Science and Pollution Research (2019),
https://hdl.handle.net/21.15107/rcub_dais_5805 .

TY  - CONF
AU  - Filipović, Suzana
AU  - Obradović, Nina
AU  - Fahrenholtz, William G.
AU  - Marinković, Bojan A.
AU  - Rogan, Jelena
AU  - Lević, S.
AU  - Pavlović, Vladimir
PY  - 2019
UR  - http://dais.sanu.ac.rs/123456789/6779
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5743
AB  - Magnesium aluminate has spinel structure and very good mechanical, chemical, and thermal properties. Owing to these properties, it has a wide range of applications including refractory ceramics, optically transparent ceramic windows and armors. Its low dielectric permeability and low loss tangent enable its using for integrated electronic devices, as well. Furthermore, as a porous ceramic, magnesium aluminate has important application as humidity sensor, catalyst and filter for waste water purification. In this paper, synthesis and characterization of MgAl2O4 was performed. Stochiometric ratio of MgO and Al2O3powders was mixed and calcined within the temperatures range 1500-1800 oC to produce pure spinel phase. Thereafter pellets were crushed and treated in planetary ball mill for 60 minutes to obtained fine grain. All powders, calcined and milled, were examined for phase composition, crystal structure, and morphology. The obtained results showed that by increasing the temperature denser samples but more fragile have been synthesized. Milling for 1 hour leads to crumble of bigger particles and getting finer, single phase powders. XRPD and Raman spectroscopy showed disorder in crystal structure after milling.
PB  - Belgrade : Serbian Ceramic Society
C3  - Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019
T1  - Morphological and structural characterization of spinel MgAl2O4
EP  - 32
SP  - 32
UR  - https://hdl.handle.net/21.15107/rcub_dais_6779
ER  - 

@conference{
author = "Filipović, Suzana and Obradović, Nina and Fahrenholtz, William G. and Marinković, Bojan A. and Rogan, Jelena and Lević, S. and Pavlović, Vladimir",
year = "2019",
abstract = "Magnesium aluminate has spinel structure and very good mechanical, chemical, and thermal properties. Owing to these properties, it has a wide range of applications including refractory ceramics, optically transparent ceramic windows and armors. Its low dielectric permeability and low loss tangent enable its using for integrated electronic devices, as well. Furthermore, as a porous ceramic, magnesium aluminate has important application as humidity sensor, catalyst and filter for waste water purification. In this paper, synthesis and characterization of MgAl2O4 was performed. Stochiometric ratio of MgO and Al2O3powders was mixed and calcined within the temperatures range 1500-1800 oC to produce pure spinel phase. Thereafter pellets were crushed and treated in planetary ball mill for 60 minutes to obtained fine grain. All powders, calcined and milled, were examined for phase composition, crystal structure, and morphology. The obtained results showed that by increasing the temperature denser samples but more fragile have been synthesized. Milling for 1 hour leads to crumble of bigger particles and getting finer, single phase powders. XRPD and Raman spectroscopy showed disorder in crystal structure after milling.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019",
title = "Morphological and structural characterization of spinel MgAl2O4",
pages = "32-32",
url = "https://hdl.handle.net/21.15107/rcub_dais_6779"
}

Filipović, S., Obradović, N., Fahrenholtz, W. G., Marinković, B. A., Rogan, J., Lević, S.,& Pavlović, V.. (2019). Morphological and structural characterization of spinel MgAl2O4. in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019
Belgrade : Serbian Ceramic Society., 32-32.
https://hdl.handle.net/21.15107/rcub_dais_6779

Filipović S, Obradović N, Fahrenholtz WG, Marinković BA, Rogan J, Lević S, Pavlović V. Morphological and structural characterization of spinel MgAl2O4. in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019. 2019;:32-32.
https://hdl.handle.net/21.15107/rcub_dais_6779 .

Filipović, Suzana, Obradović, Nina, Fahrenholtz, William G., Marinković, Bojan A., Rogan, Jelena, Lević, S., Pavlović, Vladimir, "Morphological and structural characterization of spinel MgAl2O4" in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019 (2019):32-32,
https://hdl.handle.net/21.15107/rcub_dais_6779 .

TY  - JOUR
AU  - Obradović, Nina
AU  - Fahrenholtz, William G.
AU  - Filipović, Suzana
AU  - Kosanović, Darko
AU  - Dapčević, A.
AU  - Đorđević, Antonije
AU  - Balać, Igor
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - http://www.sciencedirect.com/science/article/pii/S0272884219306340
UR  - http://dais.sanu.ac.rs/123456789/5272
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5740
AB  - Magnesium aluminate, MgAl2O4 and other alumina-based spinels are ceramics with high hardness, high melting point and mechanical strenght. Spinels can also be used as dielectrics in microwave applications. The goal of this study was to examine the effects of mechanical activation and sintering temperatures on physico-chemical properties of spinel. MgAl2O4 was produced by solid state reaction between MgO and α-Al2O3. The starting powders were mixed by ball milling to homogenize without significant particle size reduction. Mechanical activation of mixed powders was performed in a high-energy planetary ball mill in air for 1 h. Powders were compacted at 300 MPa. Heat treatments were performed in air, at temperatures ranging from 1200 to 1600 °C with 2 h dwell time, to determine the amount of spinel formation as a function of temperature. Phase composition and microstructure of initial powders and heated samples were determined by means of X-ray diffraction, particle size analysis, and scanning electron microscopy. The influences of milling and consolidation parameters were studied by electrical measurements and mechanical characterization. The main conclusion of this study was that mechanical activation for 60 min initiated a mechano-chemical reaction, resulted in spinel formation at much lower temperatures than within non-activated powders, and indicated that final sintering stage started at much lower temperatures for activated powders. Changes in microstructure parameters, as a consequence of mechanical treatment and subsequent heating of investigated powder mixtures, strongly affect electrical and mechanical properties of the final ceramics.
PB  - Elsevier
T2  - Ceramics International
T1  - The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics
EP  - 12021
IS  - 9
SP  - 12015
VL  - 45
DO  - 10.1016/j.ceramint.2019.03.095
ER  - 

@article{
author = "Obradović, Nina and Fahrenholtz, William G. and Filipović, Suzana and Kosanović, Darko and Dapčević, A. and Đorđević, Antonije and Balać, Igor and Pavlović, Vladimir B.",
year = "2019",
abstract = "Magnesium aluminate, MgAl2O4 and other alumina-based spinels are ceramics with high hardness, high melting point and mechanical strenght. Spinels can also be used as dielectrics in microwave applications. The goal of this study was to examine the effects of mechanical activation and sintering temperatures on physico-chemical properties of spinel. MgAl2O4 was produced by solid state reaction between MgO and α-Al2O3. The starting powders were mixed by ball milling to homogenize without significant particle size reduction. Mechanical activation of mixed powders was performed in a high-energy planetary ball mill in air for 1 h. Powders were compacted at 300 MPa. Heat treatments were performed in air, at temperatures ranging from 1200 to 1600 °C with 2 h dwell time, to determine the amount of spinel formation as a function of temperature. Phase composition and microstructure of initial powders and heated samples were determined by means of X-ray diffraction, particle size analysis, and scanning electron microscopy. The influences of milling and consolidation parameters were studied by electrical measurements and mechanical characterization. The main conclusion of this study was that mechanical activation for 60 min initiated a mechano-chemical reaction, resulted in spinel formation at much lower temperatures than within non-activated powders, and indicated that final sintering stage started at much lower temperatures for activated powders. Changes in microstructure parameters, as a consequence of mechanical treatment and subsequent heating of investigated powder mixtures, strongly affect electrical and mechanical properties of the final ceramics.",
publisher = "Elsevier",
journal = "Ceramics International",
title = "The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics",
pages = "12021-12015",
number = "9",
volume = "45",
doi = "10.1016/j.ceramint.2019.03.095"
}

Obradović, N., Fahrenholtz, W. G., Filipović, S., Kosanović, D., Dapčević, A., Đorđević, A., Balać, I.,& Pavlović, V. B.. (2019). The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics. in Ceramics International
Elsevier., 45(9), 12015-12021.
https://doi.org/10.1016/j.ceramint.2019.03.095

Obradović N, Fahrenholtz WG, Filipović S, Kosanović D, Dapčević A, Đorđević A, Balać I, Pavlović VB. The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics. in Ceramics International. 2019;45(9):12015-12021.
doi:10.1016/j.ceramint.2019.03.095 .

Obradović, Nina, Fahrenholtz, William G., Filipović, Suzana, Kosanović, Darko, Dapčević, A., Đorđević, Antonije, Balać, Igor, Pavlović, Vladimir B., "The effect of mechanical activation on synthesis and properties of MgAl2O4 ceramics" in Ceramics International, 45, no. 9 (2019):12015-12021,
https://doi.org/10.1016/j.ceramint.2019.03.095 . .

TY  - JOUR
AU  - Filipović, Suzana
AU  - Obradović, Nina
AU  - Marković, Smilja
AU  - Mitrić, Miodrag
AU  - Balać, Igor
AU  - Đorđević, Antonije
AU  - Pavlović, Vladimir
PY  - 2019
UR  - http://www.sciencedirect.com/science/article/pii/S0921883119302596
UR  - http://dais.sanu.ac.rs/123456789/6951
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5745
AB  - Alumina-based compounds have many technological applications and attract great attention even after decades of investigation, due to their good chemical, electrical, and mechanical properties. A mixture of several alumina modifications (α-, κ-, γ-Al2O3) doped with 1 wt% of Mn2O3 was used for this experiment. The powder was mechanically activated for 60 min in an ethanol medium. After compaction, green bodies were sintered in the temperature range from 1200 to 1400 °C. Microstructures of the obtained specimens were investigated by scanning electron microscopy (SEM) and Energy-dispersive X-ray spectroscopy (EDS). The influence of morphological changes on electrical and mechanical properties was examined in detail. We have developed a test fixture and corresponding software for measurement of the relative dielectric permittivity and the loss tangent of ceramic specimens. This new method overcomes the problems of dimensions and shape of samples, as well as the problem of applying silver paste. The accuracy is around 2% for ε'r and 0.003 for tanδ. We demonstrate that the mechanical activation (MA) has the dominant influence on lowering the characteristic temperatures and microstructure development, which further leads to increased permittivity and tensile strength.
PB  - Elsevier
T2  - Advanced Powder Technology
T1  - The effect of ball milling on properties of sintered manganese-doped alumina
EP  - 2540
IS  - 11
SP  - 2533
VL  - 30
DO  - 10.1016/j.apt.2019.07.033
ER  - 

@article{
author = "Filipović, Suzana and Obradović, Nina and Marković, Smilja and Mitrić, Miodrag and Balać, Igor and Đorđević, Antonije and Pavlović, Vladimir",
year = "2019",
abstract = "Alumina-based compounds have many technological applications and attract great attention even after decades of investigation, due to their good chemical, electrical, and mechanical properties. A mixture of several alumina modifications (α-, κ-, γ-Al2O3) doped with 1 wt% of Mn2O3 was used for this experiment. The powder was mechanically activated for 60 min in an ethanol medium. After compaction, green bodies were sintered in the temperature range from 1200 to 1400 °C. Microstructures of the obtained specimens were investigated by scanning electron microscopy (SEM) and Energy-dispersive X-ray spectroscopy (EDS). The influence of morphological changes on electrical and mechanical properties was examined in detail. We have developed a test fixture and corresponding software for measurement of the relative dielectric permittivity and the loss tangent of ceramic specimens. This new method overcomes the problems of dimensions and shape of samples, as well as the problem of applying silver paste. The accuracy is around 2% for ε'r and 0.003 for tanδ. We demonstrate that the mechanical activation (MA) has the dominant influence on lowering the characteristic temperatures and microstructure development, which further leads to increased permittivity and tensile strength.",
publisher = "Elsevier",
journal = "Advanced Powder Technology",
title = "The effect of ball milling on properties of sintered manganese-doped alumina",
pages = "2540-2533",
number = "11",
volume = "30",
doi = "10.1016/j.apt.2019.07.033"
}

Filipović, S., Obradović, N., Marković, S., Mitrić, M., Balać, I., Đorđević, A.,& Pavlović, V.. (2019). The effect of ball milling on properties of sintered manganese-doped alumina. in Advanced Powder Technology
Elsevier., 30(11), 2533-2540.
https://doi.org/10.1016/j.apt.2019.07.033

Filipović S, Obradović N, Marković S, Mitrić M, Balać I, Đorđević A, Pavlović V. The effect of ball milling on properties of sintered manganese-doped alumina. in Advanced Powder Technology. 2019;30(11):2533-2540.
doi:10.1016/j.apt.2019.07.033 .

Filipović, Suzana, Obradović, Nina, Marković, Smilja, Mitrić, Miodrag, Balać, Igor, Đorđević, Antonije, Pavlović, Vladimir, "The effect of ball milling on properties of sintered manganese-doped alumina" in Advanced Powder Technology, 30, no. 11 (2019):2533-2540,
https://doi.org/10.1016/j.apt.2019.07.033 . .

TY  - CONF
AU  - Trajković, Isaak
AU  - Obradović, Nina
AU  - Marinković, Aleksandar
AU  - Casas Luna, Mariano
AU  - Pavlović, Vladimir
PY  - 2019
UR  - http://dais.sanu.ac.rs/123456789/6920
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5744
AB  - The maximal allowed concentration (MAC) for As(V) in water decreased from 50 to 10 μg/l, by considering the harmful effects of arsenic on the environment and human health. In order to achieve the established rigorous requirements, it is necessary to develop new materials and design new forms of adsorbents that can reduce the concentration of arsenic in drinking water. In this paper, the synthesized magnetite/3D-printed wollastonite hybrid sorbent was used to remove As(V) from aqueous solutions. 3D-printed wollastonite was obtained using the 3D-printing technique from methylhydrocyclosiloxane and calcium carbonate as precursors. Synthesis of adsorption material was carried out by depositing magnetite from an iron(II)-sulfate solution by potassium hydroxide on 3D-printed wollastonite. The adsorption properties of the hybrid adsorbent depend on the properties of magnetite and its porosity. This could be achieved by modifying the processes of depositing magnetite on the porous 3D-printed wollastonite. Characterization of the obtained material was performed using FTIR, SEM and TG-DTA. An investigation of the sorption properties of hybrid adsorbents was carried out for As(V) removal - one relative to the starting pH value of the solution, the adsorbent mass, the temperature and the adsorption time. Determination of adsorption parameters was performed by applying Langmuir, Freundlich and Dubinin- Radushkevich equations. Kinetics, using pseudo-first, pseudo-second and second order equations, as well as diffusion rate were determined using Veber-Moris and HSDM models. Determination of kinetics and adhesion parameters at three different temperatures enabled the calculation of thermodynamic and activation parameters of the adsorption process, which contributed to a better understanding of the adsorption mechanism.
PB  - Belgrade : Serbian Ceramic Society
C3  - Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019
T1  - Application of magnetite/3D-printed wollastonite hybrid sorbent for As(V) removal from water
EP  - 52
SP  - 52
UR  - https://hdl.handle.net/21.15107/rcub_dais_6920
ER  - 

@conference{
author = "Trajković, Isaak and Obradović, Nina and Marinković, Aleksandar and Casas Luna, Mariano and Pavlović, Vladimir",
year = "2019",
abstract = "The maximal allowed concentration (MAC) for As(V) in water decreased from 50 to 10 μg/l, by considering the harmful effects of arsenic on the environment and human health. In order to achieve the established rigorous requirements, it is necessary to develop new materials and design new forms of adsorbents that can reduce the concentration of arsenic in drinking water. In this paper, the synthesized magnetite/3D-printed wollastonite hybrid sorbent was used to remove As(V) from aqueous solutions. 3D-printed wollastonite was obtained using the 3D-printing technique from methylhydrocyclosiloxane and calcium carbonate as precursors. Synthesis of adsorption material was carried out by depositing magnetite from an iron(II)-sulfate solution by potassium hydroxide on 3D-printed wollastonite. The adsorption properties of the hybrid adsorbent depend on the properties of magnetite and its porosity. This could be achieved by modifying the processes of depositing magnetite on the porous 3D-printed wollastonite. Characterization of the obtained material was performed using FTIR, SEM and TG-DTA. An investigation of the sorption properties of hybrid adsorbents was carried out for As(V) removal - one relative to the starting pH value of the solution, the adsorbent mass, the temperature and the adsorption time. Determination of adsorption parameters was performed by applying Langmuir, Freundlich and Dubinin- Radushkevich equations. Kinetics, using pseudo-first, pseudo-second and second order equations, as well as diffusion rate were determined using Veber-Moris and HSDM models. Determination of kinetics and adhesion parameters at three different temperatures enabled the calculation of thermodynamic and activation parameters of the adsorption process, which contributed to a better understanding of the adsorption mechanism.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019",
title = "Application of magnetite/3D-printed wollastonite hybrid sorbent for As(V) removal from water",
pages = "52-52",
url = "https://hdl.handle.net/21.15107/rcub_dais_6920"
}

Trajković, I., Obradović, N., Marinković, A., Casas Luna, M.,& Pavlović, V.. (2019). Application of magnetite/3D-printed wollastonite hybrid sorbent for As(V) removal from water. in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019
Belgrade : Serbian Ceramic Society., 52-52.
https://hdl.handle.net/21.15107/rcub_dais_6920

Trajković I, Obradović N, Marinković A, Casas Luna M, Pavlović V. Application of magnetite/3D-printed wollastonite hybrid sorbent for As(V) removal from water. in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019. 2019;:52-52.
https://hdl.handle.net/21.15107/rcub_dais_6920 .

Trajković, Isaak, Obradović, Nina, Marinković, Aleksandar, Casas Luna, Mariano, Pavlović, Vladimir, "Application of magnetite/3D-printed wollastonite hybrid sorbent for As(V) removal from water" in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019 (2019):52-52,
https://hdl.handle.net/21.15107/rcub_dais_6920 .

TY  - JOUR
AU  - Terzić, Anja
AU  - Obradović, Nina
AU  - Kosanović, Darko
AU  - Stojanović, Jovica
AU  - Djordjević, Antonije
AU  - Andrić, Ljubiša
AU  - Pavlović, Vladimir
PY  - 2019
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5028
AB  - Steatite, as ceramic with composition predominantly resting on magnesium silicate, was produced from economic resources - talc, aluminosilicate clays, and either BaCO3 or feldspar as flux. Titanium dioxide was a doping agent. Four steatite mixtures were mechanically activated in a planetary ball mill for 30, 45 or 60 min, prior to the thermal treatment. Two-step sintering with initial phase set at 1350 degrees C and holding period conducted at 1250 degrees C was applied to initiate diffusion and prevent grain growth. Thereby, a high density ceramic material with low-porous submicron structure was acquired. The effects of TiO2 addition on densification, microstructure, and dielectric characteristics of steatites were monitored. The thermal stability of green mixtures was tested by differential thermal and thermogravimetric analyses. Changes in crystallinity and mineral phase composition were observed by the X-ray diffraction technique. Microstructural visualization with spatial arrangements of individual chemical elements on surface of the sintered ceramics was acquired by scanning electron microscopy accompanied with EDS mapping. In order to test the possibility of employment of the obtained steatites in insulation materials, electrical measurements were conducted by recording variations of the dielectric constant and loss tangent as a function of alternations in the mix-design and the mechanical activation period.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Effects of mechanical-activation and TiO2 addition on the behavior of two-step sintered steatite ceramics
EP  - 3022
IS  - 3
SP  - 3013
VL  - 45
DO  - 10.1016/j.ceramint.2018.10.120
ER  - 

@article{
author = "Terzić, Anja and Obradović, Nina and Kosanović, Darko and Stojanović, Jovica and Djordjević, Antonije and Andrić, Ljubiša and Pavlović, Vladimir",
year = "2019",
abstract = "Steatite, as ceramic with composition predominantly resting on magnesium silicate, was produced from economic resources - talc, aluminosilicate clays, and either BaCO3 or feldspar as flux. Titanium dioxide was a doping agent. Four steatite mixtures were mechanically activated in a planetary ball mill for 30, 45 or 60 min, prior to the thermal treatment. Two-step sintering with initial phase set at 1350 degrees C and holding period conducted at 1250 degrees C was applied to initiate diffusion and prevent grain growth. Thereby, a high density ceramic material with low-porous submicron structure was acquired. The effects of TiO2 addition on densification, microstructure, and dielectric characteristics of steatites were monitored. The thermal stability of green mixtures was tested by differential thermal and thermogravimetric analyses. Changes in crystallinity and mineral phase composition were observed by the X-ray diffraction technique. Microstructural visualization with spatial arrangements of individual chemical elements on surface of the sintered ceramics was acquired by scanning electron microscopy accompanied with EDS mapping. In order to test the possibility of employment of the obtained steatites in insulation materials, electrical measurements were conducted by recording variations of the dielectric constant and loss tangent as a function of alternations in the mix-design and the mechanical activation period.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Effects of mechanical-activation and TiO2 addition on the behavior of two-step sintered steatite ceramics",
pages = "3022-3013",
number = "3",
volume = "45",
doi = "10.1016/j.ceramint.2018.10.120"
}

Terzić, A., Obradović, N., Kosanović, D., Stojanović, J., Djordjević, A., Andrić, L.,& Pavlović, V.. (2019). Effects of mechanical-activation and TiO2 addition on the behavior of two-step sintered steatite ceramics. in Ceramics International
Elsevier Sci Ltd, Oxford., 45(3), 3013-3022.
https://doi.org/10.1016/j.ceramint.2018.10.120

Terzić A, Obradović N, Kosanović D, Stojanović J, Djordjević A, Andrić L, Pavlović V. Effects of mechanical-activation and TiO2 addition on the behavior of two-step sintered steatite ceramics. in Ceramics International. 2019;45(3):3013-3022.
doi:10.1016/j.ceramint.2018.10.120 .

Terzić, Anja, Obradović, Nina, Kosanović, Darko, Stojanović, Jovica, Djordjević, Antonije, Andrić, Ljubiša, Pavlović, Vladimir, "Effects of mechanical-activation and TiO2 addition on the behavior of two-step sintered steatite ceramics" in Ceramics International, 45, no. 3 (2019):3013-3022,
https://doi.org/10.1016/j.ceramint.2018.10.120 . .

TY  - CONF
AU  - Obradović, Nina
AU  - Gigov, Mihajlo
AU  - Đorđević, Aleksandar
AU  - Kern, Frank
AU  - Dmitrović, Svetlana
AU  - Matović, Branko
AU  - Đorđević, Antonije
AU  - Pavlović, Vladimir B.
PY  - 2018
UR  - http://dais.sanu.ac.rs/123456789/3667
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5726
AB  - The paper presents results of investigation of the influence of mechanical activation of shungite, a Russian natural mineral rich in silica and carbon, on its sintering behavior. The mechanical activation of the starting powder was performed in a high-energy ball mill in time intervals from 0 to 480 minutes. The phase composition of the starting mixtures and sintered samples was analyzed by the X-ray diffraction method. The scanning electron microscopy was performed in order to determine changes in the microstructure. Sintering was performed at various temperatures for 2 h, in an Ar and vacuum atmosphere. Dielectric properties of the sintered samples were measured in the frequency range from 1 to 500 MHz. The obtained results indicate that sintered shungite powder is a good candidate for applications as an absorber of electromagnetic waves in microwave engineering.
PB  - Belgrade : Materials Research Society of Serbia
C3  - Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018
T1  - Shungite - a Russian mineral: possible application as a microwave absorber
EP  - 94
SP  - 94
UR  - https://hdl.handle.net/21.15107/rcub_dais_3667
ER  - 

@conference{
author = "Obradović, Nina and Gigov, Mihajlo and Đorđević, Aleksandar and Kern, Frank and Dmitrović, Svetlana and Matović, Branko and Đorđević, Antonije and Pavlović, Vladimir B.",
year = "2018",
abstract = "The paper presents results of investigation of the influence of mechanical activation of shungite, a Russian natural mineral rich in silica and carbon, on its sintering behavior. The mechanical activation of the starting powder was performed in a high-energy ball mill in time intervals from 0 to 480 minutes. The phase composition of the starting mixtures and sintered samples was analyzed by the X-ray diffraction method. The scanning electron microscopy was performed in order to determine changes in the microstructure. Sintering was performed at various temperatures for 2 h, in an Ar and vacuum atmosphere. Dielectric properties of the sintered samples were measured in the frequency range from 1 to 500 MHz. The obtained results indicate that sintered shungite powder is a good candidate for applications as an absorber of electromagnetic waves in microwave engineering.",
publisher = "Belgrade : Materials Research Society of Serbia",
journal = "Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018",
title = "Shungite - a Russian mineral: possible application as a microwave absorber",
pages = "94-94",
url = "https://hdl.handle.net/21.15107/rcub_dais_3667"
}

Obradović, N., Gigov, M., Đorđević, A., Kern, F., Dmitrović, S., Matović, B., Đorđević, A.,& Pavlović, V. B.. (2018). Shungite - a Russian mineral: possible application as a microwave absorber. in Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018
Belgrade : Materials Research Society of Serbia., 94-94.
https://hdl.handle.net/21.15107/rcub_dais_3667

Obradović N, Gigov M, Đorđević A, Kern F, Dmitrović S, Matović B, Đorđević A, Pavlović VB. Shungite - a Russian mineral: possible application as a microwave absorber. in Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018. 2018;:94-94.
https://hdl.handle.net/21.15107/rcub_dais_3667 .

Obradović, Nina, Gigov, Mihajlo, Đorđević, Aleksandar, Kern, Frank, Dmitrović, Svetlana, Matović, Branko, Đorđević, Antonije, Pavlović, Vladimir B., "Shungite - a Russian mineral: possible application as a microwave absorber" in Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018 (2018):94-94,
https://hdl.handle.net/21.15107/rcub_dais_3667 .

TY  - CONF
AU  - Filipović, Suzana
AU  - Obradović, Nina
AU  - Marković, Smilja
AU  - Đorđević, Antonije
AU  - Dapčević, Aleksandra
AU  - Rogan, Jelena
AU  - Pavlović, Vladimir B.
PY  - 2018
UR  - http://dais.sanu.ac.rs/123456789/3634
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/5725
AB  - Sintered alumina powder represents suitable material for usage in various industry fields (e.g., as chip carriers in electronics, microwaves, jewelry production), due to convenient physical properties, such as sinterability, electrical and mechanical features. Those properties can be modified by addition of different oxides and/or mechanical treatment. Therefore, in this investigation the alumina was doped with 1 wt. % of Cr2O3, Mn2O3 and NiO, respectively, followed by 1 hour of mechanical activation at 400 rpm in planetary ball mill. Sintering of powder mixtures was tracked by sensitive dilatometer up to 1400 °C. The final density values varied from cca. 2 ̶ 3.2 g/cm3. Changes in microstructure were observed by means of SEM. The influence of additives along with mechanical activation is monitored trough changes in electrical permittivity and loss tangent. Compared to pure alumina, the additives lower the relative permittivity and increase dielectric losses. For a given mixture, the sintering increases the relative permittivity and decreases losses.
PB  - Belgrade : Materials Research Society of Serbia
C3  - Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018
T1  - Sintering of alumina doped with different oxides, followed by sensitive dilatometer
EP  - 95
SP  - 95
UR  - https://hdl.handle.net/21.15107/rcub_dais_3634
ER  - 

@conference{
author = "Filipović, Suzana and Obradović, Nina and Marković, Smilja and Đorđević, Antonije and Dapčević, Aleksandra and Rogan, Jelena and Pavlović, Vladimir B.",
year = "2018",
abstract = "Sintered alumina powder represents suitable material for usage in various industry fields (e.g., as chip carriers in electronics, microwaves, jewelry production), due to convenient physical properties, such as sinterability, electrical and mechanical features. Those properties can be modified by addition of different oxides and/or mechanical treatment. Therefore, in this investigation the alumina was doped with 1 wt. % of Cr2O3, Mn2O3 and NiO, respectively, followed by 1 hour of mechanical activation at 400 rpm in planetary ball mill. Sintering of powder mixtures was tracked by sensitive dilatometer up to 1400 °C. The final density values varied from cca. 2 ̶ 3.2 g/cm3. Changes in microstructure were observed by means of SEM. The influence of additives along with mechanical activation is monitored trough changes in electrical permittivity and loss tangent. Compared to pure alumina, the additives lower the relative permittivity and increase dielectric losses. For a given mixture, the sintering increases the relative permittivity and decreases losses.",
publisher = "Belgrade : Materials Research Society of Serbia",
journal = "Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018",
title = "Sintering of alumina doped with different oxides, followed by sensitive dilatometer",
pages = "95-95",
url = "https://hdl.handle.net/21.15107/rcub_dais_3634"
}

Filipović, S., Obradović, N., Marković, S., Đorđević, A., Dapčević, A., Rogan, J.,& Pavlović, V. B.. (2018). Sintering of alumina doped with different oxides, followed by sensitive dilatometer. in Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018
Belgrade : Materials Research Society of Serbia., 95-95.
https://hdl.handle.net/21.15107/rcub_dais_3634

Filipović S, Obradović N, Marković S, Đorđević A, Dapčević A, Rogan J, Pavlović VB. Sintering of alumina doped with different oxides, followed by sensitive dilatometer. in Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018. 2018;:95-95.
https://hdl.handle.net/21.15107/rcub_dais_3634 .

Filipović, Suzana, Obradović, Nina, Marković, Smilja, Đorđević, Antonije, Dapčević, Aleksandra, Rogan, Jelena, Pavlović, Vladimir B., "Sintering of alumina doped with different oxides, followed by sensitive dilatometer" in Programme and The Book of Abstracts / Twentieth Annual Conference YUCOMAT 2018, Herceg Novi, September 3-7, 2018 (2018):95-95,
https://hdl.handle.net/21.15107/rcub_dais_3634 .

TY  - JOUR
AU  - Terzić, Anja
AU  - Obradović, Nina
AU  - Pouchly, Vaclav
AU  - Stojanović, Jovica
AU  - Maca, Karel
AU  - Pavlović, Vladimir
PY  - 2018
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4704
AB  - The influence of the sintering method on the mineral phase transformations and development of the crystalline microstructure of steatite ceramics was investigated. The steatite samples were fabricated from talc and bentonite as low-cost raw materials. Feldspar and barium carbonate, as fluxing agents, were altered in the steatite composition. Dilatometric analysis was applied in the monitoring of the dimensional changes and thereby densification of steatite during the traditional sintering (TS) procedure up to 1200 degrees C. Spark plasma sintering (SPS) method was used under the following sintering conditions: 100 degrees C/min heating rate, uniaxial pressure of 50 MPa; sintering temperature 800 degrees C/1 min or 1000 degrees C/2 min. Crystallinity changes and mineral phase transition during sintering were observed by X-ray diffraction technique. Microstructural visualization of the samples and the spatial arrangements of individual chemical elements were achieved via scanning electron microscopy equipped with the EDS mapping. It was found that SPS sintering facilitated all microstructural changes during high temperature treatment and shifted them to lower temperatures. SPS treatment conducted at 1000 degrees C resulted in maximum densification of the steatite powder compacts and the formation stabilized protoenstatite structure.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Microstructure and Phase Composition Of Steatite Ceramics Sintered by Traditional and Spark Plasma Sintering
EP  - 312
IS  - 3
SP  - 299
VL  - 50
DO  - 10.2298/SOS1803299T
ER  - 

@article{
author = "Terzić, Anja and Obradović, Nina and Pouchly, Vaclav and Stojanović, Jovica and Maca, Karel and Pavlović, Vladimir",
year = "2018",
abstract = "The influence of the sintering method on the mineral phase transformations and development of the crystalline microstructure of steatite ceramics was investigated. The steatite samples were fabricated from talc and bentonite as low-cost raw materials. Feldspar and barium carbonate, as fluxing agents, were altered in the steatite composition. Dilatometric analysis was applied in the monitoring of the dimensional changes and thereby densification of steatite during the traditional sintering (TS) procedure up to 1200 degrees C. Spark plasma sintering (SPS) method was used under the following sintering conditions: 100 degrees C/min heating rate, uniaxial pressure of 50 MPa; sintering temperature 800 degrees C/1 min or 1000 degrees C/2 min. Crystallinity changes and mineral phase transition during sintering were observed by X-ray diffraction technique. Microstructural visualization of the samples and the spatial arrangements of individual chemical elements were achieved via scanning electron microscopy equipped with the EDS mapping. It was found that SPS sintering facilitated all microstructural changes during high temperature treatment and shifted them to lower temperatures. SPS treatment conducted at 1000 degrees C resulted in maximum densification of the steatite powder compacts and the formation stabilized protoenstatite structure.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Microstructure and Phase Composition Of Steatite Ceramics Sintered by Traditional and Spark Plasma Sintering",
pages = "312-299",
number = "3",
volume = "50",
doi = "10.2298/SOS1803299T"
}

Terzić, A., Obradović, N., Pouchly, V., Stojanović, J., Maca, K.,& Pavlović, V.. (2018). Microstructure and Phase Composition Of Steatite Ceramics Sintered by Traditional and Spark Plasma Sintering. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 50(3), 299-312.
https://doi.org/10.2298/SOS1803299T

Terzić A, Obradović N, Pouchly V, Stojanović J, Maca K, Pavlović V. Microstructure and Phase Composition Of Steatite Ceramics Sintered by Traditional and Spark Plasma Sintering. in Science of Sintering. 2018;50(3):299-312.
doi:10.2298/SOS1803299T .

Terzić, Anja, Obradović, Nina, Pouchly, Vaclav, Stojanović, Jovica, Maca, Karel, Pavlović, Vladimir, "Microstructure and Phase Composition Of Steatite Ceramics Sintered by Traditional and Spark Plasma Sintering" in Science of Sintering, 50, no. 3 (2018):299-312,
https://doi.org/10.2298/SOS1803299T . .

TY  - JOUR
AU  - Filipović, Suzana
AU  - Obradović, Nina
AU  - Marković, Smilja
AU  - Djordjević, Antonije
AU  - Balac, Igor
AU  - Dapcević, Aleksandra
AU  - Rogan, Jelena
AU  - Pavlović, Vladimir
PY  - 2018
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4712
AB  - Corundum (alpha-alumina) is a suiTab. material for usage in various industry fields owing to its chemical stability, electrical and mechanical features. It is known that properties of ceramics could be modified by addition of different oxides, as well as by changing the consolidation parameters. In this respect, alumina was doped with 1 wt.% of Cr2O3, Mn2O3 and NiO, followed by 1 hour of mechanical activation in a high-energy planetary ball mill. A sensitive dilatometer was used for sintering of powder mixtures up to 1400 degrees C and recording the obtained dilatation. The final density varied between cca. 1.9 and 3.3 g/cm(3). Microstructural changes were detected by SEM measurements. Changes in electrical permittivity and loss tangent were associated with the preparation conditions (types of additives, duration of mechanical activation). For a given mixture, the sintering increases the relative permittivity and decreases losses, exhibiting the optimal values of 8.32 and 0.027, respectively, for the sample activated 60 minutes and sintered, with the addition of MnO2. Mechanical measurements indicate significant differences in strength with the addition of different transition metal oxides. Samples with Mn and Ni, activated and sintered, with strength of 121 and 86 MPa, respectively, have a significantly higher tensile strength than the other tested samples, due to their more compact microstructures.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Physical Properties of Sintered Alumina Doped with Different Oxides
EP  - 419
IS  - 4
SP  - 409
VL  - 50
DO  - 10.2298/SOS1804409F
ER  - 

@article{
author = "Filipović, Suzana and Obradović, Nina and Marković, Smilja and Djordjević, Antonije and Balac, Igor and Dapcević, Aleksandra and Rogan, Jelena and Pavlović, Vladimir",
year = "2018",
abstract = "Corundum (alpha-alumina) is a suiTab. material for usage in various industry fields owing to its chemical stability, electrical and mechanical features. It is known that properties of ceramics could be modified by addition of different oxides, as well as by changing the consolidation parameters. In this respect, alumina was doped with 1 wt.% of Cr2O3, Mn2O3 and NiO, followed by 1 hour of mechanical activation in a high-energy planetary ball mill. A sensitive dilatometer was used for sintering of powder mixtures up to 1400 degrees C and recording the obtained dilatation. The final density varied between cca. 1.9 and 3.3 g/cm(3). Microstructural changes were detected by SEM measurements. Changes in electrical permittivity and loss tangent were associated with the preparation conditions (types of additives, duration of mechanical activation). For a given mixture, the sintering increases the relative permittivity and decreases losses, exhibiting the optimal values of 8.32 and 0.027, respectively, for the sample activated 60 minutes and sintered, with the addition of MnO2. Mechanical measurements indicate significant differences in strength with the addition of different transition metal oxides. Samples with Mn and Ni, activated and sintered, with strength of 121 and 86 MPa, respectively, have a significantly higher tensile strength than the other tested samples, due to their more compact microstructures.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Physical Properties of Sintered Alumina Doped with Different Oxides",
pages = "419-409",
number = "4",
volume = "50",
doi = "10.2298/SOS1804409F"
}

Filipović, S., Obradović, N., Marković, S., Djordjević, A., Balac, I., Dapcević, A., Rogan, J.,& Pavlović, V.. (2018). Physical Properties of Sintered Alumina Doped with Different Oxides. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 50(4), 409-419.
https://doi.org/10.2298/SOS1804409F

Filipović S, Obradović N, Marković S, Djordjević A, Balac I, Dapcević A, Rogan J, Pavlović V. Physical Properties of Sintered Alumina Doped with Different Oxides. in Science of Sintering. 2018;50(4):409-419.
doi:10.2298/SOS1804409F .

Filipović, Suzana, Obradović, Nina, Marković, Smilja, Djordjević, Antonije, Balac, Igor, Dapcević, Aleksandra, Rogan, Jelena, Pavlović, Vladimir, "Physical Properties of Sintered Alumina Doped with Different Oxides" in Science of Sintering, 50, no. 4 (2018):409-419,
https://doi.org/10.2298/SOS1804409F . .

TY  - JOUR
AU  - Filipović, Suzana
AU  - Pavlović, Vera P.
AU  - Obradović, N.
AU  - Paunović, V.
AU  - Maca, Karel
AU  - Pavlović, Vladimir
PY  - 2017
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4393
AB  - In the present study the effect of preparation conditions on microstructure and electrical properties of MgTiO3 ceramics was investigated. Mixture of MgO and TiO2 powders was subjected to mechanical activation for different time periods. Two types of sintering (two-step and HIP sintering) were performed on green bodies prepared by cold isostatic pressing. AC impedance spectroscopy in the low-frequency range (from 20 Hz to 1 MHz), at room and elevated temperatures, were performed in order to separate contribution of grains and grain boundaries to capacitance, resistance and conductivity of magnesium titanate ceramics. The special attention was directed to explanation of the influence of mechanical activation on electrical and morphological changes in sintered samples. The significant decrease of partial oxygen pressure in HP sintering atmosphere caused the change from insulating behavior of MgTiO3 samples after two-step sintering to semiconducting one.
PB  - Elsevier Science Sa, Lausanne
T2  - Journal of Alloys and Compounds
T1  - The impedance analysis of sintered MgTiO3 ceramics
EP  - 115
SP  - 107
VL  - 701
DO  - 10.1016/j.jallcom.2017.01.117
ER  - 

@article{
author = "Filipović, Suzana and Pavlović, Vera P. and Obradović, N. and Paunović, V. and Maca, Karel and Pavlović, Vladimir",
year = "2017",
abstract = "In the present study the effect of preparation conditions on microstructure and electrical properties of MgTiO3 ceramics was investigated. Mixture of MgO and TiO2 powders was subjected to mechanical activation for different time periods. Two types of sintering (two-step and HIP sintering) were performed on green bodies prepared by cold isostatic pressing. AC impedance spectroscopy in the low-frequency range (from 20 Hz to 1 MHz), at room and elevated temperatures, were performed in order to separate contribution of grains and grain boundaries to capacitance, resistance and conductivity of magnesium titanate ceramics. The special attention was directed to explanation of the influence of mechanical activation on electrical and morphological changes in sintered samples. The significant decrease of partial oxygen pressure in HP sintering atmosphere caused the change from insulating behavior of MgTiO3 samples after two-step sintering to semiconducting one.",
publisher = "Elsevier Science Sa, Lausanne",
journal = "Journal of Alloys and Compounds",
title = "The impedance analysis of sintered MgTiO3 ceramics",
pages = "115-107",
volume = "701",
doi = "10.1016/j.jallcom.2017.01.117"
}

Filipović, S., Pavlović, V. P., Obradović, N., Paunović, V., Maca, K.,& Pavlović, V.. (2017). The impedance analysis of sintered MgTiO3 ceramics. in Journal of Alloys and Compounds
Elsevier Science Sa, Lausanne., 701, 107-115.
https://doi.org/10.1016/j.jallcom.2017.01.117

Filipović S, Pavlović VP, Obradović N, Paunović V, Maca K, Pavlović V. The impedance analysis of sintered MgTiO3 ceramics. in Journal of Alloys and Compounds. 2017;701:107-115.
doi:10.1016/j.jallcom.2017.01.117 .

Filipović, Suzana, Pavlović, Vera P., Obradović, N., Paunović, V., Maca, Karel, Pavlović, Vladimir, "The impedance analysis of sintered MgTiO3 ceramics" in Journal of Alloys and Compounds, 701 (2017):107-115,
https://doi.org/10.1016/j.jallcom.2017.01.117 . .

TY  - JOUR
AU  - Djordjević, Antonije
AU  - Olcan, Dragan
AU  - Obradović, Nina
AU  - Paunović, Vesna
AU  - Filipović, Suzana
AU  - Pavlović, Vladimir
PY  - 2017
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4433
AB  - Post-sintering of magnesium titanate ceramics by hot isostatic pressing (HIP) in an oxygen-free atmosphere significantly alters various electrical properties of the product. In particular, the sintered material becomes a semiconductor. The aims of this paper are: to extend our investigations of the electrical properties of this material by expanding the frequency range of measurements, to design interpolation formulas for the frequency dependence of the complex relative permittivity, and to propose HIP-sintered magnesium titanate as a material for thermistors that have a negative-temperature-coefficient resistance (NTCR), as well as for varistors.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Electrical Properties of Magnesium Titanate Ceramics Post-Sintered by Hot Isostatic Pressing
EP  - 380
IS  - 4
SP  - 373
VL  - 49
DO  - 10.2298/SOS1704373D
ER  - 

@article{
author = "Djordjević, Antonije and Olcan, Dragan and Obradović, Nina and Paunović, Vesna and Filipović, Suzana and Pavlović, Vladimir",
year = "2017",
abstract = "Post-sintering of magnesium titanate ceramics by hot isostatic pressing (HIP) in an oxygen-free atmosphere significantly alters various electrical properties of the product. In particular, the sintered material becomes a semiconductor. The aims of this paper are: to extend our investigations of the electrical properties of this material by expanding the frequency range of measurements, to design interpolation formulas for the frequency dependence of the complex relative permittivity, and to propose HIP-sintered magnesium titanate as a material for thermistors that have a negative-temperature-coefficient resistance (NTCR), as well as for varistors.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Electrical Properties of Magnesium Titanate Ceramics Post-Sintered by Hot Isostatic Pressing",
pages = "380-373",
number = "4",
volume = "49",
doi = "10.2298/SOS1704373D"
}

Djordjević, A., Olcan, D., Obradović, N., Paunović, V., Filipović, S.,& Pavlović, V.. (2017). Electrical Properties of Magnesium Titanate Ceramics Post-Sintered by Hot Isostatic Pressing. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 49(4), 373-380.
https://doi.org/10.2298/SOS1704373D

Djordjević A, Olcan D, Obradović N, Paunović V, Filipović S, Pavlović V. Electrical Properties of Magnesium Titanate Ceramics Post-Sintered by Hot Isostatic Pressing. in Science of Sintering. 2017;49(4):373-380.
doi:10.2298/SOS1704373D .

Djordjević, Antonije, Olcan, Dragan, Obradović, Nina, Paunović, Vesna, Filipović, Suzana, Pavlović, Vladimir, "Electrical Properties of Magnesium Titanate Ceramics Post-Sintered by Hot Isostatic Pressing" in Science of Sintering, 49, no. 4 (2017):373-380,
https://doi.org/10.2298/SOS1704373D . .

TY  - JOUR
AU  - Obradović, Nina
AU  - Filipović, Suzana
AU  - Rusmirović, Jelena D.
AU  - Postole, Georgeta
AU  - Marinković, Aleksandar
AU  - Radić, Danka
AU  - Rakić, Vesna
AU  - Pavlović, Vladimir
AU  - Auroux, Aline
PY  - 2017
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4477
AB  - In this paper, synthesis of porous wollastonite-based ceramics was reported. Ceramic precursor, methylhydrocyclosiloxane, together with micro-sized CaCO3, was used as starting material. After 20 min of ultrasound treatment, and calcination at 250 degrees C for 30 min, yeast as a pore-forming agent was added to the as-obtained powders. Sintering regime was set up based on the results obtained by differential thermal analysis. Prepared mixture was pressed into pallets and sintered at 900 degrees C for 1 h. After the sintering regime, porous wollastonite-based ceramics was obtained. The phase composition of the sintered samples as well as microstructures was analyzed by X-ray diffraction method and SEM. In a batch test, the influence of pH, contact time and initial ion concentration on adsorption efficiency of As+5, Cr+6, and phosphate ions on synthesized wollastonite-based ceramics were studied. Time-dependent adsorption was best described by pseudo-second-order kinetic model and Weber-Morris model that predicted intra-particle diffusion as a rate-controlling step of overall process. High adsorption capacities 39.97, 21.87, and 15.29 mgg(-1) were obtained for As+5, Cr+6, and phosphate ions, respectively.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Formation of Porous Wollastonite-based Ceramics after Sintering With Yeast as the Pore-forming Agent
EP  - 246
IS  - 3
SP  - 235
VL  - 49
DO  - 10.2298/SOS1703235O
ER  - 

@article{
author = "Obradović, Nina and Filipović, Suzana and Rusmirović, Jelena D. and Postole, Georgeta and Marinković, Aleksandar and Radić, Danka and Rakić, Vesna and Pavlović, Vladimir and Auroux, Aline",
year = "2017",
abstract = "In this paper, synthesis of porous wollastonite-based ceramics was reported. Ceramic precursor, methylhydrocyclosiloxane, together with micro-sized CaCO3, was used as starting material. After 20 min of ultrasound treatment, and calcination at 250 degrees C for 30 min, yeast as a pore-forming agent was added to the as-obtained powders. Sintering regime was set up based on the results obtained by differential thermal analysis. Prepared mixture was pressed into pallets and sintered at 900 degrees C for 1 h. After the sintering regime, porous wollastonite-based ceramics was obtained. The phase composition of the sintered samples as well as microstructures was analyzed by X-ray diffraction method and SEM. In a batch test, the influence of pH, contact time and initial ion concentration on adsorption efficiency of As+5, Cr+6, and phosphate ions on synthesized wollastonite-based ceramics were studied. Time-dependent adsorption was best described by pseudo-second-order kinetic model and Weber-Morris model that predicted intra-particle diffusion as a rate-controlling step of overall process. High adsorption capacities 39.97, 21.87, and 15.29 mgg(-1) were obtained for As+5, Cr+6, and phosphate ions, respectively.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Formation of Porous Wollastonite-based Ceramics after Sintering With Yeast as the Pore-forming Agent",
pages = "246-235",
number = "3",
volume = "49",
doi = "10.2298/SOS1703235O"
}

Obradović, N., Filipović, S., Rusmirović, J. D., Postole, G., Marinković, A., Radić, D., Rakić, V., Pavlović, V.,& Auroux, A.. (2017). Formation of Porous Wollastonite-based Ceramics after Sintering With Yeast as the Pore-forming Agent. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 49(3), 235-246.
https://doi.org/10.2298/SOS1703235O

Obradović N, Filipović S, Rusmirović JD, Postole G, Marinković A, Radić D, Rakić V, Pavlović V, Auroux A. Formation of Porous Wollastonite-based Ceramics after Sintering With Yeast as the Pore-forming Agent. in Science of Sintering. 2017;49(3):235-246.
doi:10.2298/SOS1703235O .

Obradović, Nina, Filipović, Suzana, Rusmirović, Jelena D., Postole, Georgeta, Marinković, Aleksandar, Radić, Danka, Rakić, Vesna, Pavlović, Vladimir, Auroux, Aline, "Formation of Porous Wollastonite-based Ceramics after Sintering With Yeast as the Pore-forming Agent" in Science of Sintering, 49, no. 3 (2017):235-246,
https://doi.org/10.2298/SOS1703235O . .

TY  - JOUR
AU  - Brković, Danijela V.
AU  - Pavlović, Vladimir
AU  - Pavlović, Vera P.
AU  - Obradović, Nina
AU  - Mitrić, Miodrag
AU  - Stevanović, Sanja
AU  - Vlahović, Branislav
AU  - Uskoković, Petar S.
AU  - Marinković, Aleksandar D.
PY  - 2017
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4474
AB  - The structural characteristics of polymer nanocomposites with functionalized multiwall carbon nanotubes (MWCNTs) in poly(methyl methacrylate) matrix have been studied in relation to nanofiller loading and surface functionality. Different functional groups have been covalently attached on the MWCNTs sidewalls in order to induce interfacial interactions at nanofiller/polymer interface, which resulted in an improved nanomechanical features. Structural properties of nanocomposites, studied with XRD and Raman analysis, indicated the most pronounced decrease in a degree of amorphousness for samples containing 0.5 and 1 wt% of MWCNTs functionalized with dapsone (dapson-MWCNT) and diethyl malonate (dem-MWCNT). SEM and TEM micrographs confirmed improved dispersibility of the MWCNTs modified with aromatic structure of dapsone inside PMMA matrix. A significant increase in a glass transition temperature of over 60 degrees C has been found for the 1 wt% dapson-MWCNT nanocomposite. Additional modification of dapson-MWCNT by further increasing aromaticity and voluminosity of attached moiety (fid-MWCNT), showed 30 degrees C increases in a glass transition temperature at 4 wt% of nanofiller loading, which is similar to shift of 37 degrees C with loading of MWCNTs modified with ester terminal group. A maximum increase of 56% of reduced modulus and 86% of hardness was obtained for 1 wt% loading of dapson-MWCNT nanofiller.
PB  - Wiley, Hoboken
T2  - Polymer Composites
T1  - Structural Properties of the Multiwall Carbon Nanotubes/Poly(Methyl Methacrylate) Nanocomposites: Effect of the Multiwall Carbon Nanotubes Covalent Functionalization
EP  - E489
SP  - E472
VL  - 38
DO  - 10.1002/pc.23996
ER  - 

@article{
author = "Brković, Danijela V. and Pavlović, Vladimir and Pavlović, Vera P. and Obradović, Nina and Mitrić, Miodrag and Stevanović, Sanja and Vlahović, Branislav and Uskoković, Petar S. and Marinković, Aleksandar D.",
year = "2017",
abstract = "The structural characteristics of polymer nanocomposites with functionalized multiwall carbon nanotubes (MWCNTs) in poly(methyl methacrylate) matrix have been studied in relation to nanofiller loading and surface functionality. Different functional groups have been covalently attached on the MWCNTs sidewalls in order to induce interfacial interactions at nanofiller/polymer interface, which resulted in an improved nanomechanical features. Structural properties of nanocomposites, studied with XRD and Raman analysis, indicated the most pronounced decrease in a degree of amorphousness for samples containing 0.5 and 1 wt% of MWCNTs functionalized with dapsone (dapson-MWCNT) and diethyl malonate (dem-MWCNT). SEM and TEM micrographs confirmed improved dispersibility of the MWCNTs modified with aromatic structure of dapsone inside PMMA matrix. A significant increase in a glass transition temperature of over 60 degrees C has been found for the 1 wt% dapson-MWCNT nanocomposite. Additional modification of dapson-MWCNT by further increasing aromaticity and voluminosity of attached moiety (fid-MWCNT), showed 30 degrees C increases in a glass transition temperature at 4 wt% of nanofiller loading, which is similar to shift of 37 degrees C with loading of MWCNTs modified with ester terminal group. A maximum increase of 56% of reduced modulus and 86% of hardness was obtained for 1 wt% loading of dapson-MWCNT nanofiller.",
publisher = "Wiley, Hoboken",
journal = "Polymer Composites",
title = "Structural Properties of the Multiwall Carbon Nanotubes/Poly(Methyl Methacrylate) Nanocomposites: Effect of the Multiwall Carbon Nanotubes Covalent Functionalization",
pages = "E489-E472",
volume = "38",
doi = "10.1002/pc.23996"
}

Brković, D. V., Pavlović, V., Pavlović, V. P., Obradović, N., Mitrić, M., Stevanović, S., Vlahović, B., Uskoković, P. S.,& Marinković, A. D.. (2017). Structural Properties of the Multiwall Carbon Nanotubes/Poly(Methyl Methacrylate) Nanocomposites: Effect of the Multiwall Carbon Nanotubes Covalent Functionalization. in Polymer Composites
Wiley, Hoboken., 38, E472-E489.
https://doi.org/10.1002/pc.23996

Brković DV, Pavlović V, Pavlović VP, Obradović N, Mitrić M, Stevanović S, Vlahović B, Uskoković PS, Marinković AD. Structural Properties of the Multiwall Carbon Nanotubes/Poly(Methyl Methacrylate) Nanocomposites: Effect of the Multiwall Carbon Nanotubes Covalent Functionalization. in Polymer Composites. 2017;38:E472-E489.
doi:10.1002/pc.23996 .

Brković, Danijela V., Pavlović, Vladimir, Pavlović, Vera P., Obradović, Nina, Mitrić, Miodrag, Stevanović, Sanja, Vlahović, Branislav, Uskoković, Petar S., Marinković, Aleksandar D., "Structural Properties of the Multiwall Carbon Nanotubes/Poly(Methyl Methacrylate) Nanocomposites: Effect of the Multiwall Carbon Nanotubes Covalent Functionalization" in Polymer Composites, 38 (2017):E472-E489,
https://doi.org/10.1002/pc.23996 . .

TY  - JOUR
AU  - Obradović, Nina
AU  - Filipović, Suzana
AU  - Marković, Smilja
AU  - Mitrić, Miodrag
AU  - Rusmirović, Jelena D.
AU  - Marinković, Aleksandar
AU  - Antić, Vesna
AU  - Pavlović, Vladimir
PY  - 2017
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4324
AB  - In this study, porous macro- and micro-cellular wollastonite-based ceramics was synthesized. A ceramic precursor, methylhydrocyclosiloxane, together with micro-sized CaCO3, was used as a starting material. After 20 min of ultrasound treatment, and calcination at 250 degrees C for 30 min, different pore-forming agents were added to the as-obtained powders. Differential thermal analysis was used to determine characteristic temperatures of processes occurring within powders during heating. Based on the obtained results, the sintering regime was set up. The prepared mixtures were pressed into pallets and sintered at 900 degrees C. During the sintering regime, porous wollastonite-based ceramics was obtained. The phase composition of the sintered samples, as well as the microstructures, were analyzed by using X-ray diffraction and SEM. A two-phase system was detected in all samples, CaSiO3 wollastonite and Ca2SiO4 larnite, and their ratio varied with each pore-forming agent. It was observed that the addition of different pore-forming agents resulted in significantly different microstructures. In a batch test, the influence of pH, the contact time and the initial ion concentration on the adsorption efficiency of As+5, Cr(+6)and phosphate ions on the synthesized adsorbents were studied. Time-dependent adsorption is best described by the pseudo-second-order kinetic model and the Weber-Morris model, which predict intra-particle diffusion as a rate-controlling step of the overall process. High adsorption capacities, 21.93, 23.88, and 27.29 mg g(-1), were obtained for the CaCO3-siloxane-nanocellulose sorbent, and similar/lower capacities were obtained for the CaCO3-siloxane-PMMA and CaCO3-siloxane-cotton wool adsorbents.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Influence of different pore-forming agents on wollastonite microstructures and adsorption capacities
EP  - 7468
IS  - 10
SP  - 7461
VL  - 43
DO  - 10.1016/j.ceramint.2017.03.021
ER  - 

@article{
author = "Obradović, Nina and Filipović, Suzana and Marković, Smilja and Mitrić, Miodrag and Rusmirović, Jelena D. and Marinković, Aleksandar and Antić, Vesna and Pavlović, Vladimir",
year = "2017",
abstract = "In this study, porous macro- and micro-cellular wollastonite-based ceramics was synthesized. A ceramic precursor, methylhydrocyclosiloxane, together with micro-sized CaCO3, was used as a starting material. After 20 min of ultrasound treatment, and calcination at 250 degrees C for 30 min, different pore-forming agents were added to the as-obtained powders. Differential thermal analysis was used to determine characteristic temperatures of processes occurring within powders during heating. Based on the obtained results, the sintering regime was set up. The prepared mixtures were pressed into pallets and sintered at 900 degrees C. During the sintering regime, porous wollastonite-based ceramics was obtained. The phase composition of the sintered samples, as well as the microstructures, were analyzed by using X-ray diffraction and SEM. A two-phase system was detected in all samples, CaSiO3 wollastonite and Ca2SiO4 larnite, and their ratio varied with each pore-forming agent. It was observed that the addition of different pore-forming agents resulted in significantly different microstructures. In a batch test, the influence of pH, the contact time and the initial ion concentration on the adsorption efficiency of As+5, Cr(+6)and phosphate ions on the synthesized adsorbents were studied. Time-dependent adsorption is best described by the pseudo-second-order kinetic model and the Weber-Morris model, which predict intra-particle diffusion as a rate-controlling step of the overall process. High adsorption capacities, 21.93, 23.88, and 27.29 mg g(-1), were obtained for the CaCO3-siloxane-nanocellulose sorbent, and similar/lower capacities were obtained for the CaCO3-siloxane-PMMA and CaCO3-siloxane-cotton wool adsorbents.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Influence of different pore-forming agents on wollastonite microstructures and adsorption capacities",
pages = "7468-7461",
number = "10",
volume = "43",
doi = "10.1016/j.ceramint.2017.03.021"
}

Obradović, N., Filipović, S., Marković, S., Mitrić, M., Rusmirović, J. D., Marinković, A., Antić, V.,& Pavlović, V.. (2017). Influence of different pore-forming agents on wollastonite microstructures and adsorption capacities. in Ceramics International
Elsevier Sci Ltd, Oxford., 43(10), 7461-7468.
https://doi.org/10.1016/j.ceramint.2017.03.021

Obradović N, Filipović S, Marković S, Mitrić M, Rusmirović JD, Marinković A, Antić V, Pavlović V. Influence of different pore-forming agents on wollastonite microstructures and adsorption capacities. in Ceramics International. 2017;43(10):7461-7468.
doi:10.1016/j.ceramint.2017.03.021 .

Obradović, Nina, Filipović, Suzana, Marković, Smilja, Mitrić, Miodrag, Rusmirović, Jelena D., Marinković, Aleksandar, Antić, Vesna, Pavlović, Vladimir, "Influence of different pore-forming agents on wollastonite microstructures and adsorption capacities" in Ceramics International, 43, no. 10 (2017):7461-7468,
https://doi.org/10.1016/j.ceramint.2017.03.021 . .

TY  - JOUR
AU  - Nedeljković, Borivoje
AU  - Mitrović, Nebojša
AU  - Orelj, Jelena
AU  - Obradović, Nina
AU  - Pavlović, Vladimir
PY  - 2017
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4476
AB  - In this study the characterization of FeCo-2V alloys toroidal samples produced by PIM/MIM technology was presented. The feedstock for metal injection molding (MIM) was prepared by mixing starting FeCoV powder with a low viscosity binder. Green samples were subjected to solvent debinding and subsequent thermal debinding followed by sintering. Sintering was performed during 3.5 hours from 1370 degrees C to 1460 degrees C in hydrogen atmosphere in order to attain the appropriate mechanical and magnetic properties. Microstructure, hardness HV10 and magnetic hysteresis B(H) were investigated as a function of sintering temperature. Optimum combination of functional properties was observed after sintering at temperature of 1370 degrees C. In addition, magnetic properties were analyzed as frequency dependent and successfully simulated in operating frequency range from 5 Hz to 60 Hz.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Characterization of FeCoV Alloy Processed by PIM/MIM Route
EP  - 309
IS  - 3
SP  - 299
VL  - 49
DO  - 10.2298/SOS1703299N
ER  - 

@article{
author = "Nedeljković, Borivoje and Mitrović, Nebojša and Orelj, Jelena and Obradović, Nina and Pavlović, Vladimir",
year = "2017",
abstract = "In this study the characterization of FeCo-2V alloys toroidal samples produced by PIM/MIM technology was presented. The feedstock for metal injection molding (MIM) was prepared by mixing starting FeCoV powder with a low viscosity binder. Green samples were subjected to solvent debinding and subsequent thermal debinding followed by sintering. Sintering was performed during 3.5 hours from 1370 degrees C to 1460 degrees C in hydrogen atmosphere in order to attain the appropriate mechanical and magnetic properties. Microstructure, hardness HV10 and magnetic hysteresis B(H) were investigated as a function of sintering temperature. Optimum combination of functional properties was observed after sintering at temperature of 1370 degrees C. In addition, magnetic properties were analyzed as frequency dependent and successfully simulated in operating frequency range from 5 Hz to 60 Hz.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Characterization of FeCoV Alloy Processed by PIM/MIM Route",
pages = "309-299",
number = "3",
volume = "49",
doi = "10.2298/SOS1703299N"
}

Nedeljković, B., Mitrović, N., Orelj, J., Obradović, N.,& Pavlović, V.. (2017). Characterization of FeCoV Alloy Processed by PIM/MIM Route. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 49(3), 299-309.
https://doi.org/10.2298/SOS1703299N

Nedeljković B, Mitrović N, Orelj J, Obradović N, Pavlović V. Characterization of FeCoV Alloy Processed by PIM/MIM Route. in Science of Sintering. 2017;49(3):299-309.
doi:10.2298/SOS1703299N .

Nedeljković, Borivoje, Mitrović, Nebojša, Orelj, Jelena, Obradović, Nina, Pavlović, Vladimir, "Characterization of FeCoV Alloy Processed by PIM/MIM Route" in Science of Sintering, 49, no. 3 (2017):299-309,
https://doi.org/10.2298/SOS1703299N . .

TY  - JOUR
AU  - Terzić, Anja
AU  - Obradović, Nina
AU  - Stojanović, Jovica
AU  - Pavlović, Vladimir
AU  - Andrić, Ljubiša
AU  - Olcan, Dragan
AU  - Djordjević, Antonije
PY  - 2017
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4491
AB  - The focus of the study was on providing insights into interconnections between sintering and development of the crystalline microstructure, and consequently variations in dielectric behavior of four steatites fabricated from a low-cost raw material, i.e. talc. The changes, induced by the alternations of the binders (bentonite, kaolin clay) and fluxing agents (BaCO3, feldspar), were monitored in the temperature range 1000 degrees to 1250 degrees C in which complete densification and re-crystallization of the investigated structures were accomplished. The critical points in the synthesis of steatite materials were assessed by instrumental analyses. Crystallinity changes and mineral phase transition during sintering were monitored by X-ray diffraction technique. Microstructural visualization of the samples and the spatial arrangements of individual chemical elements were achieved via scanning electron microscopy accompanied with EDS mapping. The thermal stability was observed on the green mixtures using differential thermal and thermo gravimetric analyses. Electrical measurements recorded variations of the dielectric constant (epsilon(r)) and loss tangent (tan delta) as a function of the sintering temperature. The investigation highlighted critical design points, as well as the optimal combinations of the raw materials for production of the steatite ceramics for advanced electrical engineering applications.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Influence of different bonding and fluxing agents on the sintering behavior and dielectric properties of steatite ceramic materials
EP  - 13275
IS  - 16
SP  - 13264
VL  - 43
DO  - 10.1016/j.ceramint.2017.07.024
ER  - 

@article{
author = "Terzić, Anja and Obradović, Nina and Stojanović, Jovica and Pavlović, Vladimir and Andrić, Ljubiša and Olcan, Dragan and Djordjević, Antonije",
year = "2017",
abstract = "The focus of the study was on providing insights into interconnections between sintering and development of the crystalline microstructure, and consequently variations in dielectric behavior of four steatites fabricated from a low-cost raw material, i.e. talc. The changes, induced by the alternations of the binders (bentonite, kaolin clay) and fluxing agents (BaCO3, feldspar), were monitored in the temperature range 1000 degrees to 1250 degrees C in which complete densification and re-crystallization of the investigated structures were accomplished. The critical points in the synthesis of steatite materials were assessed by instrumental analyses. Crystallinity changes and mineral phase transition during sintering were monitored by X-ray diffraction technique. Microstructural visualization of the samples and the spatial arrangements of individual chemical elements were achieved via scanning electron microscopy accompanied with EDS mapping. The thermal stability was observed on the green mixtures using differential thermal and thermo gravimetric analyses. Electrical measurements recorded variations of the dielectric constant (epsilon(r)) and loss tangent (tan delta) as a function of the sintering temperature. The investigation highlighted critical design points, as well as the optimal combinations of the raw materials for production of the steatite ceramics for advanced electrical engineering applications.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Influence of different bonding and fluxing agents on the sintering behavior and dielectric properties of steatite ceramic materials",
pages = "13275-13264",
number = "16",
volume = "43",
doi = "10.1016/j.ceramint.2017.07.024"
}

Terzić, A., Obradović, N., Stojanović, J., Pavlović, V., Andrić, L., Olcan, D.,& Djordjević, A.. (2017). Influence of different bonding and fluxing agents on the sintering behavior and dielectric properties of steatite ceramic materials. in Ceramics International
Elsevier Sci Ltd, Oxford., 43(16), 13264-13275.
https://doi.org/10.1016/j.ceramint.2017.07.024

Terzić A, Obradović N, Stojanović J, Pavlović V, Andrić L, Olcan D, Djordjević A. Influence of different bonding and fluxing agents on the sintering behavior and dielectric properties of steatite ceramic materials. in Ceramics International. 2017;43(16):13264-13275.
doi:10.1016/j.ceramint.2017.07.024 .

Terzić, Anja, Obradović, Nina, Stojanović, Jovica, Pavlović, Vladimir, Andrić, Ljubiša, Olcan, Dragan, Djordjević, Antonije, "Influence of different bonding and fluxing agents on the sintering behavior and dielectric properties of steatite ceramic materials" in Ceramics International, 43, no. 16 (2017):13264-13275,
https://doi.org/10.1016/j.ceramint.2017.07.024 . .

TY  - JOUR
AU  - Obradović, Nina
AU  - Djordjević, Nataša
AU  - Filipović, Suzana
AU  - Marković, Smilja
AU  - Kosanović, Darko
AU  - Mitrić, Miodrag
AU  - Pavlović, Vladimir
PY  - 2016
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4192
AB  - Since cordierite, 2MgO center dot 2Al(2)O(3)center dot 5SiO(2) (MAS), is a very useful high-temperature ceramic material, it is important to decrease its sintering temperature. In order to accelerate the process of sintering, 5.00 mass% MoO3 was added to the starting mixtures. The mechanical activation of the starting mixtures was performed in a high-energy ball mill in time intervals from 0 to 160 min. After the activation, starting mixtures were sintered at 1300 A degrees C for 2 h. In order to determine the impact of mechanical activation on particle size distribution and powders morphology, the mechanically treated powders were characterized by a laser light-scattering particle size analyzer and scanning electron microscopy. The phase composition of the starting mixtures and sintered samples was analyzed by the X-ray diffraction method. In order to determine temperature intervals of chemical reactions and phase transitions, differential thermal analyses (DTA) and thermo-gravimetric analysis were used. Kissinger's equation was employed to calculate apparent activation energies of various processes that occur within the system during heating. Based on the obtained DTA results, it was established that mechanical activation along with MoO3 additive has influence on sintering temperature which was decreased for more than 100 A degrees C, comparing to the literature data.
PB  - Springer, Dordrecht
T2  - Journal of Thermal Analysis and Calorimetry
T1  - Reaction kinetics of mechanically activated cordierite-based ceramics studied via DTA
EP  - 673
IS  - 2
SP  - 667
VL  - 124
DO  - 10.1007/s10973-015-5132-9
ER  - 

@article{
author = "Obradović, Nina and Djordjević, Nataša and Filipović, Suzana and Marković, Smilja and Kosanović, Darko and Mitrić, Miodrag and Pavlović, Vladimir",
year = "2016",
abstract = "Since cordierite, 2MgO center dot 2Al(2)O(3)center dot 5SiO(2) (MAS), is a very useful high-temperature ceramic material, it is important to decrease its sintering temperature. In order to accelerate the process of sintering, 5.00 mass% MoO3 was added to the starting mixtures. The mechanical activation of the starting mixtures was performed in a high-energy ball mill in time intervals from 0 to 160 min. After the activation, starting mixtures were sintered at 1300 A degrees C for 2 h. In order to determine the impact of mechanical activation on particle size distribution and powders morphology, the mechanically treated powders were characterized by a laser light-scattering particle size analyzer and scanning electron microscopy. The phase composition of the starting mixtures and sintered samples was analyzed by the X-ray diffraction method. In order to determine temperature intervals of chemical reactions and phase transitions, differential thermal analyses (DTA) and thermo-gravimetric analysis were used. Kissinger's equation was employed to calculate apparent activation energies of various processes that occur within the system during heating. Based on the obtained DTA results, it was established that mechanical activation along with MoO3 additive has influence on sintering temperature which was decreased for more than 100 A degrees C, comparing to the literature data.",
publisher = "Springer, Dordrecht",
journal = "Journal of Thermal Analysis and Calorimetry",
title = "Reaction kinetics of mechanically activated cordierite-based ceramics studied via DTA",
pages = "673-667",
number = "2",
volume = "124",
doi = "10.1007/s10973-015-5132-9"
}

Obradović, N., Djordjević, N., Filipović, S., Marković, S., Kosanović, D., Mitrić, M.,& Pavlović, V.. (2016). Reaction kinetics of mechanically activated cordierite-based ceramics studied via DTA. in Journal of Thermal Analysis and Calorimetry
Springer, Dordrecht., 124(2), 667-673.
https://doi.org/10.1007/s10973-015-5132-9

Obradović N, Djordjević N, Filipović S, Marković S, Kosanović D, Mitrić M, Pavlović V. Reaction kinetics of mechanically activated cordierite-based ceramics studied via DTA. in Journal of Thermal Analysis and Calorimetry. 2016;124(2):667-673.
doi:10.1007/s10973-015-5132-9 .

Obradović, Nina, Djordjević, Nataša, Filipović, Suzana, Marković, Smilja, Kosanović, Darko, Mitrić, Miodrag, Pavlović, Vladimir, "Reaction kinetics of mechanically activated cordierite-based ceramics studied via DTA" in Journal of Thermal Analysis and Calorimetry, 124, no. 2 (2016):667-673,
https://doi.org/10.1007/s10973-015-5132-9 . .

TY  - JOUR
AU  - Kosanović, Darko
AU  - Obradović, N.
AU  - Pavlović, Vera P.
AU  - Marković, S.
AU  - Maricić, A.
AU  - Rasić, G.
AU  - Vlahović, Branislav
AU  - Pavlović, Vladimir
AU  - Ristić, M.M.
PY  - 2016
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4010
AB  - Crystal structure and morphology of mechanically activated nanocrystalline Fe/BaTiO3 was investigated using a combination of spectroscopic and microscopic methods. These show that mechanical activation led to the creation of new surfaces and the comminution of the initial powder particles. Prolonged milling resulted in formation of larger agglomerates of BaTiO3 and bimodal particle size distribution, where BaTiO3 particles were significantly larger than those of iron-containing phases. Milling times of 210 min and above lead to a significant decrease in temperature of the oxidation of iron in the sample, indicating abrupt change in reactivity. Raman spectroscopy analysis has revealed that activation had a pronounced influence on Fe/BaTiO3 lattice, thereby affecting both the stability of the crystal structure and the phase transition phenomena.
PB  - Elsevier, Amsterdam
T2  - Materials Science and Engineering B-Advanced Functional Solid-State Materials
T1  - The influence of mechanical activation on the morphological changes of Fe/BaTiO3 powder
EP  - 95
SP  - 89
VL  - 212
DO  - 10.1016/j.mseb.2016.07.016
ER  - 

@article{
author = "Kosanović, Darko and Obradović, N. and Pavlović, Vera P. and Marković, S. and Maricić, A. and Rasić, G. and Vlahović, Branislav and Pavlović, Vladimir and Ristić, M.M.",
year = "2016",
abstract = "Crystal structure and morphology of mechanically activated nanocrystalline Fe/BaTiO3 was investigated using a combination of spectroscopic and microscopic methods. These show that mechanical activation led to the creation of new surfaces and the comminution of the initial powder particles. Prolonged milling resulted in formation of larger agglomerates of BaTiO3 and bimodal particle size distribution, where BaTiO3 particles were significantly larger than those of iron-containing phases. Milling times of 210 min and above lead to a significant decrease in temperature of the oxidation of iron in the sample, indicating abrupt change in reactivity. Raman spectroscopy analysis has revealed that activation had a pronounced influence on Fe/BaTiO3 lattice, thereby affecting both the stability of the crystal structure and the phase transition phenomena.",
publisher = "Elsevier, Amsterdam",
journal = "Materials Science and Engineering B-Advanced Functional Solid-State Materials",
title = "The influence of mechanical activation on the morphological changes of Fe/BaTiO3 powder",
pages = "95-89",
volume = "212",
doi = "10.1016/j.mseb.2016.07.016"
}

Kosanović, D., Obradović, N., Pavlović, V. P., Marković, S., Maricić, A., Rasić, G., Vlahović, B., Pavlović, V.,& Ristić, M.M.. (2016). The influence of mechanical activation on the morphological changes of Fe/BaTiO3 powder. in Materials Science and Engineering B-Advanced Functional Solid-State Materials
Elsevier, Amsterdam., 212, 89-95.
https://doi.org/10.1016/j.mseb.2016.07.016

Kosanović D, Obradović N, Pavlović VP, Marković S, Maricić A, Rasić G, Vlahović B, Pavlović V, Ristić M. The influence of mechanical activation on the morphological changes of Fe/BaTiO3 powder. in Materials Science and Engineering B-Advanced Functional Solid-State Materials. 2016;212:89-95.
doi:10.1016/j.mseb.2016.07.016 .

Kosanović, Darko, Obradović, N., Pavlović, Vera P., Marković, S., Maricić, A., Rasić, G., Vlahović, Branislav, Pavlović, Vladimir, Ristić, M.M., "The influence of mechanical activation on the morphological changes of Fe/BaTiO3 powder" in Materials Science and Engineering B-Advanced Functional Solid-State Materials, 212 (2016):89-95,
https://doi.org/10.1016/j.mseb.2016.07.016 . .

TY  - JOUR
AU  - Filipović, Suzana
AU  - Obradović, N.
AU  - Pavlović, Vladimir
AU  - Mitrić, M.
AU  - Djordjević, Antonije
AU  - Kachlik, Martin
AU  - Maca, Karel
PY  - 2016
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4209
AB  - The aim of this study is to explore the influence of the processing route on the structural and physical properties of bulk MgTiO3 ceramics. Commercially available MgO and TiO2 powders were mechanically activated in a planetary ball mill. Green bodies were formed by an isostatic pressure of 300 MPa. The sintering of these samples was done either by the Two-Step Sintering (TSS) approach or by conventional pressureless sintering followed by Hot Isostatic Pressing (post-HIPing). The first set of compacts was sintered by TSS in air at 1300 degrees C for 30 min and the next step was performed at 1200 degrees C for 20 h. The density of the obtained samples after the two-step sintering reached almost 90% of the theoretical density (%TD). The second set of compacts was sintered at 1400 degrees C for 30 min in air. The samples without open porosity were post-sintered by the HIP at 1200 degrees C for 2 h in an argon atmosphere at a pressure of 200 MPa. The density significantly increased up to 96%TD. The differences between samples prepared by these two techniques were also analyzed by XRD and SEM. The lattice vibration spectra were obtained using Raman spectroscopy and they indicate a high degree of lattice disorder, as well as high values of the oxygen vacancy concentration. Electrical characteristic were established in the frequency range from 10 kHz to 10 GHz. The choice of the processing route had considerable influence on structural and physical properties of MgTiO3 ceramics.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Effect of consolidation parameters on structural, microstructural and electrical properties of magnesium titanate ceramics
EP  - 9898
IS  - 8
SP  - 9887
VL  - 42
DO  - 10.1016/j.ceramint.2016.03.088
ER  - 

@article{
author = "Filipović, Suzana and Obradović, N. and Pavlović, Vladimir and Mitrić, M. and Djordjević, Antonije and Kachlik, Martin and Maca, Karel",
year = "2016",
abstract = "The aim of this study is to explore the influence of the processing route on the structural and physical properties of bulk MgTiO3 ceramics. Commercially available MgO and TiO2 powders were mechanically activated in a planetary ball mill. Green bodies were formed by an isostatic pressure of 300 MPa. The sintering of these samples was done either by the Two-Step Sintering (TSS) approach or by conventional pressureless sintering followed by Hot Isostatic Pressing (post-HIPing). The first set of compacts was sintered by TSS in air at 1300 degrees C for 30 min and the next step was performed at 1200 degrees C for 20 h. The density of the obtained samples after the two-step sintering reached almost 90% of the theoretical density (%TD). The second set of compacts was sintered at 1400 degrees C for 30 min in air. The samples without open porosity were post-sintered by the HIP at 1200 degrees C for 2 h in an argon atmosphere at a pressure of 200 MPa. The density significantly increased up to 96%TD. The differences between samples prepared by these two techniques were also analyzed by XRD and SEM. The lattice vibration spectra were obtained using Raman spectroscopy and they indicate a high degree of lattice disorder, as well as high values of the oxygen vacancy concentration. Electrical characteristic were established in the frequency range from 10 kHz to 10 GHz. The choice of the processing route had considerable influence on structural and physical properties of MgTiO3 ceramics.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Effect of consolidation parameters on structural, microstructural and electrical properties of magnesium titanate ceramics",
pages = "9898-9887",
number = "8",
volume = "42",
doi = "10.1016/j.ceramint.2016.03.088"
}

Filipović, S., Obradović, N., Pavlović, V., Mitrić, M., Djordjević, A., Kachlik, M.,& Maca, K.. (2016). Effect of consolidation parameters on structural, microstructural and electrical properties of magnesium titanate ceramics. in Ceramics International
Elsevier Sci Ltd, Oxford., 42(8), 9887-9898.
https://doi.org/10.1016/j.ceramint.2016.03.088

Filipović S, Obradović N, Pavlović V, Mitrić M, Djordjević A, Kachlik M, Maca K. Effect of consolidation parameters on structural, microstructural and electrical properties of magnesium titanate ceramics. in Ceramics International. 2016;42(8):9887-9898.
doi:10.1016/j.ceramint.2016.03.088 .

Filipović, Suzana, Obradović, N., Pavlović, Vladimir, Mitrić, M., Djordjević, Antonije, Kachlik, Martin, Maca, Karel, "Effect of consolidation parameters on structural, microstructural and electrical properties of magnesium titanate ceramics" in Ceramics International, 42, no. 8 (2016):9887-9898,
https://doi.org/10.1016/j.ceramint.2016.03.088 . .

TY  - JOUR
AU  - Obradović, Nina
AU  - Filipović, Suzana
AU  - Djordjević, Nataša
AU  - Kosanović, Darko
AU  - Marković, Smilja
AU  - Pavlović, Vladimir
AU  - Olcan, Dragan
AU  - Djordjević, Antonije
AU  - Kachlik, Martin
AU  - Maca, Karel
PY  - 2016
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4019
AB  - The mechanical activation can help reduce production costs and modify cordierite-based materials. In this study, the structure and electrical properties of the mechanically activated MgO-Al2O3-SiO2 system have been analyzed. The mixtures of MgO-Al2O3-SiO2 powders were mechanically activated in a planetary ball mill for time periods ranging from 0 to 160 min. Structural investigations were performed on the obtained powders. The effects of activation and a two-step sintering process on the microstructure and crystal structure were investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The thermal stability was analyzed using DTA. Electrical measurements showed variations of the dielectric constant (epsilon(r)) and loss tangent (tan delta) as a function of the time of mechanical treatment.
PB  - Elsevier Sci Ltd, Oxford
T2  - Ceramics International
T1  - Effects of mechanical activation and two-step sintering on the structure and electrical properties of cordierite-based ceramics
EP  - 13918
IS  - 12
SP  - 13909
VL  - 42
DO  - 10.1016/j.ceramint.2016.05.201
ER  - 

@article{
author = "Obradović, Nina and Filipović, Suzana and Djordjević, Nataša and Kosanović, Darko and Marković, Smilja and Pavlović, Vladimir and Olcan, Dragan and Djordjević, Antonije and Kachlik, Martin and Maca, Karel",
year = "2016",
abstract = "The mechanical activation can help reduce production costs and modify cordierite-based materials. In this study, the structure and electrical properties of the mechanically activated MgO-Al2O3-SiO2 system have been analyzed. The mixtures of MgO-Al2O3-SiO2 powders were mechanically activated in a planetary ball mill for time periods ranging from 0 to 160 min. Structural investigations were performed on the obtained powders. The effects of activation and a two-step sintering process on the microstructure and crystal structure were investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The thermal stability was analyzed using DTA. Electrical measurements showed variations of the dielectric constant (epsilon(r)) and loss tangent (tan delta) as a function of the time of mechanical treatment.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Ceramics International",
title = "Effects of mechanical activation and two-step sintering on the structure and electrical properties of cordierite-based ceramics",
pages = "13918-13909",
number = "12",
volume = "42",
doi = "10.1016/j.ceramint.2016.05.201"
}

Obradović, N., Filipović, S., Djordjević, N., Kosanović, D., Marković, S., Pavlović, V., Olcan, D., Djordjević, A., Kachlik, M.,& Maca, K.. (2016). Effects of mechanical activation and two-step sintering on the structure and electrical properties of cordierite-based ceramics. in Ceramics International
Elsevier Sci Ltd, Oxford., 42(12), 13909-13918.
https://doi.org/10.1016/j.ceramint.2016.05.201

Obradović N, Filipović S, Djordjević N, Kosanović D, Marković S, Pavlović V, Olcan D, Djordjević A, Kachlik M, Maca K. Effects of mechanical activation and two-step sintering on the structure and electrical properties of cordierite-based ceramics. in Ceramics International. 2016;42(12):13909-13918.
doi:10.1016/j.ceramint.2016.05.201 .

Obradović, Nina, Filipović, Suzana, Djordjević, Nataša, Kosanović, Darko, Marković, Smilja, Pavlović, Vladimir, Olcan, Dragan, Djordjević, Antonije, Kachlik, Martin, Maca, Karel, "Effects of mechanical activation and two-step sintering on the structure and electrical properties of cordierite-based ceramics" in Ceramics International, 42, no. 12 (2016):13909-13918,
https://doi.org/10.1016/j.ceramint.2016.05.201 . .

TY  - JOUR
AU  - Obradović, Nina
AU  - Filipović, Suzana
AU  - Djordjević, Nataša
AU  - Kosanović, Darko
AU  - Pavlović, Vladimir
AU  - Olcan, Dragan
AU  - Djordjević, Antonije
AU  - Kachlik, Martin
AU  - Maca, Karel
PY  - 2016
UR  - http://aspace.agrif.bg.ac.rs/handle/123456789/4026
AB  - Cordierite-based ceramic materials are attracting much interest for their various applications in industry, for manufacturing multilayer circuit boards, catalytic converters, filters, thermal insulation, kiln furniture, components of portable electronic devices, etc. In order to reduce production costs and modify cordierite-based materials, mechanical activation can be used. In this study, microstructural and electrical properties of mechanically activated MgO-Al2O3-SiO2 system have been analyzed. The mixtures of MgO-Al2O3-SiO2 powders were mechanically activated in a planetary ball mill for the time periods from 0 to 160 min. Morphological investigations have been performed on the obtained powders. The effects of activation and two-step sintering process on microstructure were investigated by scanning electron microscopy (SEM). Electrical measurements showed variations of the dielectric constant (epsilon(r)) and loss tangent (tan delta) as a function of time of mechanical treatment.
PB  - Međunarodni Institut za nauku o sinterovanju, Beograd
T2  - Science of Sintering
T1  - Microstructural and Electrical Properties of Cordierite-based Ceramics Obtained After Two-step Sintering Technique
EP  - 165
IS  - 2
SP  - 157
VL  - 48
DO  - 10.2298/SOS1602157O
ER  - 

@article{
author = "Obradović, Nina and Filipović, Suzana and Djordjević, Nataša and Kosanović, Darko and Pavlović, Vladimir and Olcan, Dragan and Djordjević, Antonije and Kachlik, Martin and Maca, Karel",
year = "2016",
abstract = "Cordierite-based ceramic materials are attracting much interest for their various applications in industry, for manufacturing multilayer circuit boards, catalytic converters, filters, thermal insulation, kiln furniture, components of portable electronic devices, etc. In order to reduce production costs and modify cordierite-based materials, mechanical activation can be used. In this study, microstructural and electrical properties of mechanically activated MgO-Al2O3-SiO2 system have been analyzed. The mixtures of MgO-Al2O3-SiO2 powders were mechanically activated in a planetary ball mill for the time periods from 0 to 160 min. Morphological investigations have been performed on the obtained powders. The effects of activation and two-step sintering process on microstructure were investigated by scanning electron microscopy (SEM). Electrical measurements showed variations of the dielectric constant (epsilon(r)) and loss tangent (tan delta) as a function of time of mechanical treatment.",
publisher = "Međunarodni Institut za nauku o sinterovanju, Beograd",
journal = "Science of Sintering",
title = "Microstructural and Electrical Properties of Cordierite-based Ceramics Obtained After Two-step Sintering Technique",
pages = "165-157",
number = "2",
volume = "48",
doi = "10.2298/SOS1602157O"
}

Obradović, N., Filipović, S., Djordjević, N., Kosanović, D., Pavlović, V., Olcan, D., Djordjević, A., Kachlik, M.,& Maca, K.. (2016). Microstructural and Electrical Properties of Cordierite-based Ceramics Obtained After Two-step Sintering Technique. in Science of Sintering
Međunarodni Institut za nauku o sinterovanju, Beograd., 48(2), 157-165.
https://doi.org/10.2298/SOS1602157O

Obradović N, Filipović S, Djordjević N, Kosanović D, Pavlović V, Olcan D, Djordjević A, Kachlik M, Maca K. Microstructural and Electrical Properties of Cordierite-based Ceramics Obtained After Two-step Sintering Technique. in Science of Sintering. 2016;48(2):157-165.
doi:10.2298/SOS1602157O .

Obradović, Nina, Filipović, Suzana, Djordjević, Nataša, Kosanović, Darko, Pavlović, Vladimir, Olcan, Dragan, Djordjević, Antonije, Kachlik, Martin, Maca, Karel, "Microstructural and Electrical Properties of Cordierite-based Ceramics Obtained After Two-step Sintering Technique" in Science of Sintering, 48, no. 2 (2016):157-165,
https://doi.org/10.2298/SOS1602157O . .