Претраживање
Приказ резултата 1-10 од 21
Synthesis and Sintering of High-temperature Composites Based on Mechanically Activated Fly Ash
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2012)
Amount of fly ash which is and yet to be generated in the coming years highlights the necessity of developing new methods of the recycling where this waste can be reused in significant quantity. A new possibility for fly ...
Mechanical-Chemical Synthesis Ba0.77Sr0.23TiO3
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2012)
Barium-Strontium-Titanate Ba0.77Sr0.23TiO3 was prepared from starting materials BaCO3, SrCO3 and TiO2 through solid-state reactions. Mixtures of these oxides are mechanically activated in a high-energy planetary ball mill ...
The Influence of Mechanical Activation on Sintering Process of BaCO3-SrCO3-TiO2 System
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2012)
In this article the influence of mechanical activation on sintering process of barium-strontium-titanate ceramics has been investigated. Both non-activated and mixtures treated in a planetary ball mill for 5, 10, 20, 40, ...
Study of Dielectric Behavior and Electrical Properties of Hematite alpha-Fe2O3 Doped with Zn
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2012)
The effects of Zn-doping on the dielectric behavior and electrical properties of bulk alpha-Fe2O3 have been studied. X-ray diffraction analysis revealed the presence of two phases in all samples: hematite and spinel ZnFe2O4, ...
Sintering Process Influence on Microstructure and Intergranular Impedance of Rare-Earth Modified BaTiO3-Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
Sintering process is a complex of different synergetic effects during the ceramics materials consolidation. The microstructural level properties control is very important as a stage in advanced materials prognosis. SEM ...
Sintering of Mechanically Activated Magnesium-titanate and Barium-zinc-titanate Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
In this article the influence of mechanical activation on sintering process of magnesium-titanate and barium-zinc-titanate ceramics has been investigated. Both non-activated and mixtures treated in planetary ball mill for ...
Analysis and Modeling of Sintering of Sr-hexaferrite Produced by PIM Technology
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
The powder injection moulding (PIM) technology is lately becoming more and more significant due to complex design possibilities and good repeatability. This technology requires optimization of all steps starting with ...
Electrical Properties and Microstructure Fractal Analysis of Magnesium-Modified Aluminium-Silicate Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
The addition of Mg(2)(NO)(3) and some active additives, composed of Al salts, to the mixtures of kaolinite and bentonite can provide clay compositions which, after sintering at high temperatures, produce very porous ceramics ...
Isothermal kinetics of titanium-oxo-alkoxy clusters formation
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2011)
In this article, the influences of titanium tetraisopropoxide Ti(OR)4 (R = Pri) concentration, molar ratio, h = [H2O]/[Ti(OR)4], and temperature, on the formation kinetics of the titanium-oxo-alkoxy clusters (TOAC), were ...
Synthesis of Barium-zinc-titanate Ceramics
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2012)
Mixtures of BaCO3, ZnO and TiO2 powders, with molar ratio of 1:2:4, were mechanically activated for 20, 40 and minutes in a planetary ball mill. The resulting powders were compacted into pellets and isothermally sintered ...